The initial goal here is to produce a knit fabric using lace transfers in the familiar way, but the knit carriage will now be set to slip <–>, selecting needles with each pass. In routine lace patterning the KC is set for plain knit, does not preselect needles, advance the mylar, punchcard, or other electronic patterning.
If this image, where all blue squares represent knit stitches and white squares unworked ones, was provided with the intent of its being produced as a piece of knit on the machine, the initial approach might be to use a single prong tool to move the edge of the blue in one stitch to the right for a decrease, and out one needle to the left for an increase. When the decrease is made on the bottom curve, the needle from which the stitch was taken is put back out of work. When an increase is made, a stitch is moved to work on left, and the last stitch on that side is transferred onto it. As knitting continues, that now empty needle location will create an eyelet.
I decided to wing it for the first swatches. This illustrates the same knit shape. Blue rows represent all knit rows and stitches, the empty pairs of rows leave areas to insert lace eyelets in pattern.
A second transfer to the right is included in the pattern close to the left edge of the trim to create eyelets next to the decreases, matching those eyelets created by stitches moving out in the increase segment of the chart
Now reducing it all to black and white squares or pixels for first preselection from right hand side using an electronic. This repeat is not suitable for use in a punchcard machine even though it is 24 stitches wide. Electronics advance a design row with each pass of the carriage when cam buttons are pushed in and with both carriages set to needle select. Punchcard machines in those circumstances do not advance when the alternate carriage is brought into work from the opposite side. This charted repeat is usable as is on an unaltered 910, with the first preselection row from right to left. LC operates from the left, KC from the right.
For use with Ayab software two other things need consideration. Ayab mirrors lace repeats, so either mirror the repeat of the original design, or choose action mirror in the software prior to knitting. This is a screen grab of the repeat used for my initial swatch test. I later changed the section where the diamonds cross in at the center of the eyelet repeats In addition: those first 2 rows need to be all knit, so the top row of the design was moved down to row 1 position.
KC preselects left to right, knits black squares to left, preselects same needle selection again to knit those same stitches traveling back to its home on the right, creating the two knit rows that in “normal lace” would be worked with the KC simply set to knit. As the KC now knits the second row, it preselects needles for the first row of transfers, rests on the right
LC transfers to right as it travels to left, preselects the next row of transfers. As it moves back to left it transfers to left, preselects for first of 2 all knit rows, rests on left
The sequence is repeated until the piece reaches the required length.
End needle selection is off on both carriages. As LC travels to left, because of no end needle selection, the first needle on the right is not selected. An option is to manually pull that needle out to insure it knits. I decided I actually preferred the chain created by those single stitches knitting only every other row, but was not happy with the elongated stitches on alternate rows edge stitches on the increase side. These would be the carriage actions To review: end needle selection is off on both carriages. As LC travels to left, because of no end needle selection, the first needle on the right is not selected. An option is to manually pull that needle out to insure it knits. I decided I actually preferred the chain created by those single stitches knitting only every other row. I had a serious yarn tangle on the right about halfway up the swatch, with some of the evidence visible in the approximate center of the swatch photo
My fiber is now a crisp cotton, unmarked weight, tension 8, and it is much easier to observe areas that may still be a problem to me as the designer. Ideally I would prefer the lines created by the transfers marked in cyan to match the quality of those immediately below or to the ascending part of the diamond on their opposite side, that would require changes in the transfers sequences and space between knit rows. The LC non selected stitches on the straight creating an every other row slipped stitch are still something I like. The difference on the edge stitches in the ascending angle are happening because with each transfer out, there is a single thickness of yarn on the new edge stitch and moving the stitch over a needles space elongates it. Longer loops btw are also created when single increases are made by bringing needles into work on the carriage side prior to knitting a row across all needles. In the trim’s decrease edges, the transfers in each new edge stitch have double the yarn thickness contributing to a different appearance, highlighted with magenta arrows. There are 2 rows that have no edge transfers programmed intentionally in the center before reversing direction, so that area has no resulting edge eyelet. The last shot at adjusting the repeat, with improvement in those cyan marked areas. Plain knit rows may be added between each repeat, the edge of the knit will be different than in the remaining trim on each side
Going back to the wheel that has already been invented, how can pre drawn published mk lace repeats be used instead of “winging it” endlessly or not having the confidence to perform the necessary assigning symbols and proceeding with the required separation? Still trying to work with a pattern that knits for 2 rows, transfers for 2, a chart from Stitch World:marking the 2 all knit rows that will be plain knit by programming black squares The pattern is actually for an all over lace. All the transfers in the central diamond actually are happening in the same direction. If the repeat was programmed in the usual manner, beginning with LC on the left, those transfers on the first design row and in the whole of the center diamond shape would all be to the left. I can live with them all being to the right, and would be interested in more eyelets at the edge of the trim. Here is a new repeat, with the increased eyelets at the curved edge Remember if using ayab to mirror the above repeat (seen on right) prior to preparing to knit it There is a disruption for 2 rows in the very center of the diamond, where no increases or decreases occur on the shaped edge prior to reversing the shaping. It was there in the earlier sample marked with arrows as well, but not as noticeable where the edge was created with the addition of single eyelets on increase and decrease rows.
Not finding any other candidates to alter for this purpose in stitch world at the moment I am left with the option of going back to the Brother punchcard book collections, and reviewing what needs to be changed for those same patterns that work so well with the KC set to plain knit but are now to be knit with the KC set to slip <—–>……
a lace punchcard repeat with transfers in opposite directions Assigning colors to transfers: red to left, blue to right. In theory the same repeat could be used flipped horizontally for operating the lace carriage from the right. Yellow lines highlight the 2 blank rows in card that will be replaced by black squares/ pixels (remember rules are different for slip and lace in punchcard knitting)Since the goal is a trim, things are rearranged for knitting to begin on the full 24 stitches There are 2 ways to get the above repeat to work, one is by adding extra blank rows. I chose to reverse positions for transfers, moving left transfers upon row, and red down one row. With lace carriage operating from the left this is my new repeat, with edge shaping added for trim edgeKC is set to slip after the first preselection row, first set of transfers is selected on its second pass to the right. The first transfers with the LC are made to the right, the second set to the left. If knitting the repeat using Ayab remember the above is mirrored by the software, so choose action mirror prior to configuring
This would be my test repeat for knitting the same trim in ayab with the LC operating from the right. The software would mirror it, no action needed. The last row is shifted to the bottom to allow for the knit carriage finding a home on the left. First row knit would preselect 2 needles only, with KC then set to slip in both directions, the next two rows should knit, preselecting the first row of transfers to be made by the LC operating from the right.
I am unable to test the repeat. I have had intermittent problems with patterning in the sofware from the time I installed the kit. In multiple efforts and restarts I am now getting no selection at all or wrong selection with LC operating from right, while rows advance in the software and beeps continue. I have knit lace with the LC on the right before, but not with the KC selecting needles as well. Possible solutions and causes to be determined. 3/8/18 I have been told upon testing by others the same issues have been encountered that I did when using the KC to select from left and the LC from right, and the problem appears to be the result of a bug in the software to be addressed in future updates.
3/10/18: an adaptation of Susanna’s automatically shaped trim for Brother KM, p. 223 of “A Machine Knitter’s Guide to Creating Fabrics”. This chart shows the first rows of the published punchcard. Please note: using my own lace carriage, when I tested canceling end needle selection, the problem was not solved. Brother setting recommendations made for a similar transfer pattern in an edging published by them, are given and repeat is pictured at end of my post.
Row 1: LC moves to right, no needles selected
Row 2: LC moves to left, preselects next row of transfers
Row 3: LC moves to right, transfers preselected needles to right (red dots), selects needles (if any) for next pass to left
Row 4: LC travels to and transfers to left (green dots), preselects for first row to be knit by KC In this particular pattern the direction of the arrows match the direction of the transfers with movements of LC operating from left
Row 5: KC from right, set to slip <€” €”> knits all needles in D position, repeats the same selection as it travels to left (yellow marks)
Row 6: KC travels back to right, in the second shaped knit row, preselects for the next transfers to be made by the LC
Row 7: LC travels to and transfers to right, preselects for next row of transfers
Row 8: LC travels to left, transferring to left if any needles have been preselected on the previous pass, and the process continues
The numbers on the punchcard chart do not reflect actual row numbers in knitting because when row 4, 10, etc is reached, on the next pass (a blank row in the card), the card does not advance and the previous selection is repeated. For each carriage to make an even number of passes to travel to and from its original position, the total length of the repeat must be an even number of rows.
Here are the 24 stitch repeats adjusted for knitting on the electronic. A for an unaltered 910, B indicating direction of transfers (red to right, green to left). Arrows mark the problem row, and my solution to it C on the far right, along with the repeat adjusted for use with Ayab.the ayab screen image for working the edging Both KC and LC are set not to select first and last needles in my directions. When the decreases start to happen on the left of the chart, because the end needle selection for transfer to right again does not happen in areas marked with magenta arrows, there is an extra stitch that remains on the left that does not get transferred (orange dot) so it is not knit off and simply get held as subsequent rows of knitting take place. Restoring needle selection in the LC is not a solution for the problem, so the final repeat has been amended by me to get that edge transfer. The pattern starts on cast on 20, not the full 24 stitches. Ayab knitters: use the LC to begin selection from left. The first pass will select for a knit row, push those needles back to B, and the LC will select for transfers to right on the next row as it moves to the left. When knitting is to take place there is a clear distinction in the number of selected needles (black squares). The KC will be set to slip <– –>. Make certain to remember to return the remaining 4 of the 24 total stitches back to B so the full repeat is in work on the needle bed before continuing in pattern, otherwise there will be needles there to accept stitches moved over for increases to left.
The two extra passes of the LC in this method result in a 2 stitch border on the increasing and decreasing angles of the piece, creating a much nicer edge than that in the samples at the top of the post. The eyelet so close to the right edge stitch which also winds up being slipped every other row made for very messy loose stitches in the thicker cotton that I could not control. The sample did better when I pulled the non selected needles on knit rows out to hold prior to moving across them with KC.
When working on electronics the 24 stitch limit in width for the repeat is no longer there, extra knit stitches may be easily added to the right of the pairs of eyelets along the non shaped edge. Having those extra stitches knit on the right side of the repeat made it possible for me to use my cotton again, giving me a controllable edge on that side without having to pull stitches out to make them knit. To my eye, I find the extra passes with the LC and those extra knit stitches on the right are well worth the effort and planning in the finished piece
Something to try: I found instructions ascribed to Brother
for another version of an edging using a pattern that has the same eyelet sequences along the shaped edgings. Their recommendation for a 950i is to remove the non selection mechanism on the lace carriage, and mention was made of the “rubber wheels on the carriage” being uppermost, allowing the end needles to be selected. My lace carriage has fixed, old fashioned brushes, not rubber wheels, and my eliminating end needle selection did not solve the problem with that single stitch in the center of the repeat. And if there is not enough to keep track of, this also combines fine lace and traditional transfer lace, would work fine as just lace.
3/15/18 after more testing I have come to the conclusion that end needle selection cancellation on my 910 LC is working properly, but is not operative when I am working with the my Ayab interface.