Category: Swatches and Experiments

Wisteria cousin 2, also called fern leaf, hand technique

In seminar days this was referred to as a “fern leaf” pattern. Holding groups in these sequences givea a bit more swing to the side of the finished piece. Directions for this fabric may be found in  the post 

The difference between the fabrics below and the ones that look like this swatch is that when the row of held sequences is completed from one side to the other, at least 2 rows are knit across all stitches before reversing the holding direction and moving toward the starting side to complete the repeat.
In addition, there is often a tension change between the groups that pull the fabric inward and enhance the texture. In my sample, the held segments were knit at tension 6, and the tight rows at tension 3.
The pattern in this swatch is executed on a multiple of 8 stitches 
To knit: cast on the required number of stitches, the first four rows are tight, so waste yarn and ravel cord followed by the cast-on and tight rows are recommended.
At T3 knit 4 rows, COR. Set the machine to hold stitches.
T6: bring all but the first 8 needles closest to the carriage into hold.
Knit 12 rows.
COR: on the side opposite to the carriage but closest to the needles in the working position, bring a group of 4 more needles into work. Knit one row.
COL: on the side opposite the carriage bring 4 needles into hold.
You will now again be working on a group of 8 needles. * Knit 11 rows.
COR: on the side opposite carriage bring 4 needles into work, knit one row.
COL: on the side opposite carriage bring 4 needles back into hold.*
Repeat *to* until the last set of 8 needles are in work on the left-hand side, knit 12 rows, ending COL.
T3 knit 4 rows.
Reverse the process, moving in the opposite direction, beginning with knitting 12 rows on the first group of 8 stitches on the left.

If the goal is to retain the texture, a yarn with “memory” ie wool is recommended; if a yarn such as acrylic, which has the capacity of being “killed” when pressed (sometimes the desired effect) is used,  the result may be seen below

lacing up a sample with knit i-cord

I had previously shared other images of this type of fabric, they may be found in my previous post, described as “horizontal cables“. The sequences there illustrate the use of other results from varying the number of stitches and rows in each held group, as to the biasing that results when all rows of groups move in a single direction. A bit on the possibility of automating such fabrics using slip stitch. 

Holding/short rows: hand tech to chart to automating with slip stitch 1

These directions apply to Brother Machines; designs could be used as they are and programmed into Passaps, other brands would require some adjustments. In these samples, the holes resulting from holding for 2-row sequences are considered part of the design. Vertical strips in different colors could be knit and later joined. The final result is a “zig-zag” pattern. Written directions may read: to begin, cast on, and knit 2 rows. **COR: set the machine for holding. Place in hold all except the first 2 needles on the right (carriage side). Knit 2 rows. Return to work the next group of 2 needles on the left to work, knit 2 rows. Repeat until only 2 needles on the far left are in  hold, return them to work, knit one row (color 1 in the chart below). COL: pull the first 2 needles at far right to hold, knit 2 rows, repeat until last 2 are left in hold, knit 2 rows (color 2). COL: bring next 2 needles into work, knit 2 rows, continue until the last 2 stitches are returned to work on the right, knit one row (color 3). COR: pull first 2 needles on left into hold, knit 2 rows; repeat until last 4 stitches at right are put back into work, knit 2 rows**, and repeat from **. Knit 2 rows at end of the desired number of repeats bind off.
The sorting out hand tech sequences to achieve the desired shapes sample: When producing my charts for using slip stitch to automate holding I like to draw what I would actually be knitting for each row, each stitch and row being a filled square, so the colored areas below represent knit stitches/rows on each row, the blank squares the stitches in holding. I test the repeat as a hand technique first, before in my case marking the mylar, then essentially fill in the knit stitches with color, keeping in mind the location of the knit carriage and the direction of the knitting. The colored squares are then programmed as punched holes, black squares, or pixels, and the pattern may be knit using slip stitch <—>. Needle selection needs to be canceled, otherwise, the yarn will be knit on the side of non-selected needles on that last stitch, creating a long float. The selection row needs to be toward the first 2 knit rows sequence. Here they are knit beginning on the right for 2 rows, so the selection row is made from left to right.  Odd rows move, knitting, from right to left, even rows from left to right. At this point, I prefer mac numbers for charting.

the final repeat, working chart the mylarthe swatch

The  above repeat could be considered composed of 2 pairs of stacked, mirrored triangles, here is an instance of playing single “triangles”

the mylar repeat its accompanying swatch

Pretend/ mock cables 2

I  had begun this post eons ago, and somehow it became a UFO. A recent discussion on Ravelry re using elastic yarns brought this swatch to mind, and here is the start of a return to the cable pretender category.

Big Pretender: this fabric is thread lace, using elastic for one yarn, and very fine mohair for other: a useful fabric for tightly fitting garments or garment sections, without the hand transfers or the rigidity of an all-over cabled item. The positions for the 2 yarns are reversed, so they both will knit the unpunched areas of the card, and where there are punched holes the elastic will create floats, pulling on the knit only stitches in the alternate yarn, creating the surface blistering.

the punchcard

Some suggestions for working with elastic yarn: the nature of the fabric created when knitting with elastic ie in FI is greatly affected by the yarn used, the elastic used, and the pattern being knit. Larger swatches than usual are required to estimate gauge for use of the resulting fabric in garments, at least 100 sts by 100 rows. If using a pre-drawn motif, doubling width and height may be a quick way to make up for “shrinkage” of the pattern. As with all fussy yarns make certain the elastic flows freely and is not getting hung up on the bottom of the cone. Sometimes if loose tension is not enough to make it manageable, the upper tension dial may be bypassed completely. Edges of fabric will be cleaner if the elastic knits on the end needle at least every other row. This is one fabric that benefits from the use of weights. Steaming helps the elastic to spring back after finishing the piece, test small areas, and best temp on your own iron.

A series of publications using a technique published much earlier in Japanese books as swatch samples “magic cables” by Ricky Mundstock, tuck stitch, and hooking up / ruching stitches combine to create the illusion.

more to follow

My recent knits

More of the extended twill FI, chenille  and rayon or wool combinations

In addition to all the usual suspects, I have been playing with DBJ once again, keeping my Passap battery charged, crossing my fingers that my ancient Dell laptop will keep working, playing with colors, using super thin yarns and plying them as needed

using built in patterns

my own pattern inspired from weaving drafts, borders mirrored to match direction when scarf is worn

Drop stitch lace, 2 colors per row, Passap KM

A recent Ravelry forum thread resulted in this response from me re drop stitch patterns with multiple colors per row: “some random thoughts on these techniques: they are often much easier on the Passap, particularly the E 6000 because the machine is capable of separating colors for techniques that would require software or lots of hand/brain work to be done manually and entered. The drawback is that the pattern books offer no explanations of the programmable techniques, simply offer a number to the program to reproduce a specific illustration in their publication, and need to be analyzed by DIYers if one chooses to apply them to their own patterns.
Sorting it all out can help reproduce the fabrics when using other KM brands.
In the case of multiple color patterns: to retain some of the knit structure for each color accompanied by long stitches in the same color on any single row, some of the stitches need to be knit only on the ribber or Passap back bed, with the alternating stitches in the same color dropping after they are knit on the patterning bed.
Distinctions are sometimes made in Passap knitting between release stitches and summer fair isle. For these techniques, weights are recommended. All stitches are transferred to the back bed after cast on and before beginning a release pattern.
The racking handle is down, black strippers are recommended.
The back bed pushers must be in the rest position after the pattern is set up.
All stitches are released from the front bed before binding off on the back one.
E6000 Tech 256: knit 2 rows with yarn, 2 without yarn, dropping stitches
Tech 129: N/LX end release, single color
Tech 185: N/LX 2 rows color 1, 2 rows color 2, end release
Self-drawn reader technique for 3 colors  Self-drawn reader technique for 4 colors Tech 117 for color separated designs and entered for 3+4 colorwork. From my E6 manual with my scribbled notes In tech 185 when combining the technique with a stitch pattern, the white squares for each design row K1R, skip 3, the black squares slip for 2R, K1R, skip one, with each 2 col row expanding into 4. Stitches are picked up on patterning bed EOR (odd #), not on even, resulting in both knit and dropped stitches in each color, in the pattern. BX with left arrow key/LX, 2 rows with yarn, 2 with no yarn to drop loops on the front bed. The “long stitch” Tech 184 or “pintuck” Tech 250 may also be used for release stitch.
The front bed stitches must be released before any shaping as well as prior to binding off. The edges of the resulting knits can be uneven. The side opposite that in which color changes are happening, right on Passap, left on Japanese machines, tends to be looser than the other. When color changes happen the floats on the edge between them can pull up the fabric on that side, so a small wight may have to be added and moved up every few rows on that side every few rows to keep that from happening.
Passap knitters: see summer fair isle pp 41-43 E6000 pattern book for illustrations of some 2 colors per design row stitch patterns…I am guessing also that separating colors for selective stitch dropping can help where one wants to retain some stitches while dropping others in that same row using pusher selection selectively (such as in the Superba-inspired bubble sample).
Below is a quick E6 sample: the fabric was pressed, had been much more textured prior to doing so, and is shown in sideways format; casting on and binding off would have to be considered in planning an actual fabric, as the patterned portion is a very different width than simple stocking stitch in the same yarn.
An Australian woman, Faye Butcher, developed a tool intended for dropping stitches without disrupting pusher selection on the front bed It may be used to drop any individual rows, but with some practice, it can be shifted from one side to the other, preceding the locks as they move to the opposite side, dropping loops formed on the previous row ahead of new ones being knit making the process very quick.
The Passap test swatch
purl side knit side Passap stitch formation is more predictable and even than in Brother knitting.  I prefer to drop at regular intervals, in my experience with longer pieces, not all stitches may ravel properly after doing so in a test swatch.
End release does not work in every design,  ie if long stitch shapes are distributed on knit striped grounds.
A Brother sample using the same design repeat as in the Passap swatch.

Studio simple lace on Brother electronics

this method works for studio simple lace patterns, wherein a single pass the stitches are both transferred and knit. There has been information published on using Studio punchcards on Brother punchcard machines using the KC to select, followed the LC, each making single passes. My two previous posts on the topic: 2011/05/18/lace-cards-use-on-the-brother-260-bulky/ and  2013/03/17/studio-simple-lace-punchcards-used-on-brother/.
While working out yet another HK to MK lace pattern, I sorted out the following method for using Studio simple lace on the electronic KM. It is a method that does not work on the Brother punchcard to produce the same fabric, however; on punchcard machines, as either carriage is moved to select from the opposite side of the bed, the card will not advance on the first pass, interrupting selection. I tried a swatch and got a very different lace design; depending on the starting pattern the results may be interesting (do not use elongation), but not the ones intended to match any original.

The knitting samples shown below were knit on a Brother 910. On electronic machines, as seen in previous posts on knitting with 2 carriages, the mylar (or otherwise programmed) repeat advances a row with each pass of the carriage, no matter on which side of the bed the pass originates. Dropped stitches are harder to repair in these fabrics than in patterns for multiple transfer lace (there knitting can be unraveled to the start of a sequence where 2 or more knit rows usually occur), so checking transfers, gate pegs, and adjusting stitch size and weights matter even more. There is no need to mirror the image horizontally; draw repeat as is on punchcard onto mylar

start knitting with KC (knit carriage) on left, Lace Carriage (LC) on Right

program pattern double length
on the first row the LC selects, the next row it will transfer; LC always makes 2 passes toward the KC, even if those 2 rows in repeat have no needle selection, and is removed from bed to be returned to the bed on the opposite side after the knit row with KC that follows
KC knits a single row to the opposite side
LC is placed back onto the machine opposite the KC to make 2 passes
KC follows with a single knit row, and the last 2 steps are repeated
3 total carriage passes complete one row of knit
the chart below shows the actions and placement of carriages

this sample was knit beginning with lace carriage on left, as can be seen in marked areas, the alternating repeats have a different quality in the sets of transfers marked red vs green

the “successful” swatch knit beginning with KC on left, LC on right in the method described above

December 7, 2018: an interesting method using 2 lace carriages found on youtube

 

Large eyelet lace, hand transferred (or not)

This is a lace sample created on a dubied industrial knitting machine

I became curious as to how to duplicate it and decided to use needle selection to help track the transfers rather than counting needles by hand. The repeat is a small one, suitable for both electronics and punchcards. Below is its configuration on my 910, punchcard knitters may want to flip the repeat to match the directions for knitting as written.

the sample’s knit side

its purl side

yarn: 2/8wool

end needle selection (KCII here) must be used any time there are needles out of work in the pattern

transfers are always made toward the carriage

single empty needled are put OOW after transfers across row

pairs of empty needles after they are created are returned to work before the next row of knitting to create side-by-side loops

in  my case, odd rows transfers were —>, even <—

single rows are knit after each set of transfers

1.KCII <—, transfer selected needles <—, move empty needles OOW

2. select row 2 as carriage knits —>, transfer selected needles —>, there will be two empty needles, side by side; bring all needles in work across the row

3. knit <—here there will be 2 loops side by side on adjoining emptied needles; check that no loops have dropped off, rehang and adjust tension if needed; transfer selected needles toward the carriage _ move single now emptied needles OOW

as this row and the next row are knit and transferred, side-by-side loops will become stitches, and another 2-loop set will be created

4. knit —>, transfer selected needles —> onto the adjoining loop, there will be 2 empty needles side by side, bring all/pairs needles in work across the row

repeat steps 3 and 4 for the remainder of the fabric

my previous posts on large eyelet lace were created using the lace carriage
large eyelets, and diagonal large eyelets

a cousin of sorts may be achieved by using the following punchcard lace repeat; the lace carriage selects and transfers for 4 passes, the knit carriage follows with 2 rows of knitting throughout; stitches are transferred, doubled up, and transferred again, so yarn choice, weight, and tension may need a lot of editing.

the resulting fabric

There is an added post on automating such large meshes published in July 2020 

A bubbles cousin

This is a Superba drop stitch fabric, using the same principles as those in the last post, with a rib stitch outlining the alternating drop stitch shapes on the purl side

directions from the manual

In my knit sample the ribber does all the knitting every row and patterning is accomplished on the main bed, reversing the recommendation in the Superba manual

the new repeat

Set up is so that needle selection position once again begins with 5 stitches on the left, occurs in a multiple of 5, with extra needles in work on ribber on either side

Transfer all stitches to ribber, begin needle selection with first five stitches on left in work, 3 OOW, 5 in work, 3 OOW across the bed as seen in the illustration above, reversing the beds.

The first needle, then every 4th, and last on right on the main bed will never be dropped, are always in work.

When needle selection changes to block number 2 from left, the center 3 sts of every group of 5 every needle rib sections are dropped, the empty 3 needles beginning with the second group from left are brought into work, repeating the process across the bed.

Knitting continues until needle selection changes, *the middle 3 stitches of each 5 stitch EON rib group are dropped, the previously 3 empty needles in the opposing sets are returned to work. Knitting continues until the needle selection changes* and the * * process is repeated.

Cast on and bind off methods are determined by end-use and personal preference

the resulting fabric, purl side

the knit side (not truly reversible as  the swatch in the last post)

a not so bubbly bubble end

More knit bubbles

The topic of “those bubbles” has recently turned up again on Ravelry, where another forum member (Tanya /It makesyousmile) had come across a Russian video by Anna Kovin, with results that closely resembled those in the blue sweater and blankets pictured in my previous post, and poses a great solution for knitting the alternating, the same side knit and purl variants of the stitch. I knit my samples on my Passap, simply because I tend not to keep my ribber on my Brother machine. My production is on a single bed for most pieces in that gauge, and I find it easier to both see and work without the ribber on. That said, the method can work on any machine.

Drop stitch makes for a very loose, wide fabric, so casting on and binding off needs to accommodate that. I often will start with waste yarn, a loose first row, end the piece with a loose row. My bind-off is often around 2 gate pegs or more if needed, and rehanging the bottom and binding off, in the same manner, has top and bottom match. I did not do this in my swatch, and it is easy to see where some of the problems may be.

For swatching I chose to hang the comb with the first knit pass (open cast on trick) on the back bed (would be the main bed on Brother), using a multiple of 5 stitches, knit several rows, and then transferred in a 5/5 rib configuration, sorting out the proper tension for my yarn. I began with 5 stitches on the back bed (main bed in Japanese KM), transferred the next 5 to ribber, and repeated the process across the width of my fabric. The front bed/ ribber was set at half pitch when the pattern was about to start, with an extra needle on left. The portions of the bed that create the long stitches will essentially be knitting an every needle rib, so if point to point is used to make transfers easier, it needs to be changed back to proper pitch for the remainder of the knitting. The swatch does not address the best beginning and end of the fabric for any possible end-use

1. set up 5X5 rib, begin by leaving the first five needles on the main bed (passap back bed)

2. bring all main bed needles into work (ribber needles at this point will be 5 out of work, 5 in across bed)

3. knit 8 rows

4. drop off groups of 5 stitches on the main bed, begin with the second group of 5 from the left, moving across the bed (every needle rib section), pushing groups of needles out of work as they are emptied

5. bring all the ribber needles into work (main bed needles at this point will be 5 out of work, 5 in across bed)

6. knit 8 rows

7. now drop ribber stitches, 5 at a time, begin with first 5 on the left, and continue across the bed, pushing all the needles out of work as they are emptied

repeat the process, beginning with step 2, through 7

the relaxed fabric, the knit blocks alternating knit and purl

the same swatch, illustrating what happens when you press acrylic, and some of the problems to be sorted out in terms of the start and end of any piece in this type of fabric

my previous post

The Brother version, with aid of patterning for needle selection: this particular version of the fabric is actually created by rectangular blocks of every needle rib, with straight side edges. If one wanted recognizable shapes other than this circle illusion, then more hand manipulation would be needed. The chart below illustrates the repeats for my swatch (4 sts X 6 rs or 6 X 6 would be suitable for punchcard KMs). The solid squares represent every needle rib sections, where stitches will be dropped to create the larger ones.

With the machine set to KC and no cam buttons in work, needles are selected, but no patterning occurs. “Air knitting” can help establish where on the needle bed the pattern repeats, and how to set up the needles and stitches to be in sync with selection as the work progresses.

An alternative approach using this method begins with all needles on the main bed in use as opposed to ribber ones as in my Passap test. Once the sequence is understood starting points for creating full needle rib can be varied, as can selecting the first row from either side. For these swatches, I used a thinner yarn, in a bright color, which can help identify any issues in stitch formation, and I began the swatch in rib, to see the effect that might have as well.

my amended repeat

Begin by checking needle selection, set up rib as described at top of the post, beginning the first group of 5 stitches on left with selected needles, next group not selected, etc. If all the steps are repeated beginning on the same side of the KM it does not matter which block of needles are at the opposite end,  allowing for width/gauge adjustment. I like to mark my needle bed with a water-soluble pen so I will be certain to have proper needles in work, not relying on memory or my sometimes “creative note keeping”.

CO ENR (every needle rib) set up with first needle on left in work on ribber, last on right on the main bed, racking at half-pitch: knit 1-row N/N, hang comb and weights, 2 rows circular (using opposite part buttons), follow with one row N/N

rack slightly to the right to make needle transfer easier, set up a multiple of 5 X 5 rib; begin with transferring first 5 on left down to ribber, pushing any empty ribber needles OOW; after the transfer, rack back to the original position so first ribber needle in work will once again be on left

bring all main bed needles into work (ribber needles at this point will be 5 in work, 5 out of work across the bed)

select your first pattern row, KC II (no end needle selection), continue to knit until needle selection changes so the second block from the left on the main bed is selected; nonselected needles on the main bed will now be dropped off, and those same emptied needles will be pushed completely out of work (the first group from left is the starting point here as well)

bring all needles into work on the ribber, knit until needle selection changes with all in main bed needles in B position, at that point I brought all remaining main bed empty needles between them out to hold/ D position in order to drop stitches on ribber between them, using the main bed as a guide, pushing any newly emptied ribber needles completely out of work as stitches were dropped (beginning with the second group of “5” from left)

as one physically looks at the stitches, there will actually be a count of six between MB needles, in my first sample, I dropped in series of 5, always beginning on the same left side.

This swatch shows the resulting fabric. Of note is that one side (marked with red) is holding together along dropped stitches far better than on the right (marked in black), a desirable trait, and not as noticeable in the previous swatch knit on Passap, perhaps because of the difference in the weight of the yarn and stitch size

the result was much improved when only the center 4 of the 6 ribber stitches were dropped, producing a bit of a chain stitch on each side and with a better definition of dropped stitch areas; both sides of the fabric are shown below

at this point all main bed needles are in work, needle selection will once more begin on left; knit until needle selection changes, continue the sequence.

Cast on ENR rib edge has obvious width, bind off is around 2 gate pegs after transferring any remaining ribber stitches up to main bed.

The version of the stitch as worked out by Tanya Cunningham with her shared instructions for what she refers to as “bubble pops” may be found on Ravelry.

A random slip stitch

During my early morning surfing, I recently came across a pattern knit as fair isle that I thought might work well in slip stitch

the repeat

the first sample knit side

its purl side, showing the typical slip “floats”

The light color is a 2/8 wool, the green a rayon/nylon blend, thinner in weight; the rayon flattened considerably after steaming (something to consider if the maximum texture is the desired aim); the first wide band of green is 32 rows high (full repeat), the narrower stripes occur with changes every 16 rows. Slip stitch striping can vary a pattern greatly, sometimes more successfully than others. My sample was knit on a 910, using color reverse. In the first repeat chart the white squares are intended to be what knits, the dark grey the slipped areas (Passap use same repeat, tech 129, each black square is a slipped stitch with lock set to LX rather than KX). This repeat is too wide as-is for use on a punchcard but was it usable, all but the dark squares would be punched.

The obvious color changes may take place every 32 rows, every 16, every 8, every 4, 2 followed by 6, and more. The pattern may also be knit with the same color rotation, but beginning striping sequences on a different row. The purl side of this particular pattern helps make it easy to track the location of color changes, but with many slip patterns the same may not be so obvious, and good note keeping of sequences and starting rows for the design can be a time saver when one wants to reproduce particular pleasing or successful “random” segments.

more variations

the top section here begins with the first design row KC–>

these are done with beginning the pattern on row 2, KC<–

swatch is not pressed, resulting in a more pronounced texture

Re_editing the repeat can help change/ plan the areas for solid color blocks to occur on the knit side. Slipped stitches become elongated ones on the front, knit side of the fabric, and the color they assume has to do with the last row knit before the needles with that color yarn. If a color changer is in use, the repeats must be an even number of rows in height. The repeat below is a variation of the one above. The slipped stitches are numbered, with the assumption that in this case, the fabric will be all one color, or with changes at the start and end of each repeat (now 16 rows)

Below are some of the options for color changes, with slip stitch areas renumbered as any of the colors create knit stitches on the face of the fabric, the bar at bottom of the chart indicates starting color prior to the first needle selection row toward color changer. Only 2 colors are in use in the actual knitting, the other color blocks in slipped areas are to help visualize what stitches are being slipped and for how many rows, in each color

Personal fabric and surface preferences may vary greatly between individuals. The swatch below shows variations in the above, including some dropped stitches that were “missed”

My personal preference is for the top of the swatch, where the difference in yarn weight also results in an interesting dimensional effect

a couple of the many sources on this particular stitch type

…