Category: Hints and Tips

A complex published transfer lace to electronic repeat for download/ GIMP editing


Lace on the machine can render beautiful fabrics that closely resemble hand knitting, but programming very long repeats is a challenge both in placing every hole in the correct square in a punchcard and in programming individual pixels on a mylar or as pixels for download correctly. I found the “leaf lace” repeat below shared frequently on Pinterest and thought I would test the approach discussed in the post on using numbers and gimp to create images for electronic downloads. Because it is 16 stitches wide, it is not suitable for punchcard knitting, which requires a factor of (4, 6, 8, 12) and up to a 24 stitch maximum width.

The published pattern on the left is shown as shared on Pinterest. In turn, in was captured, opened in Gimp, and magnified. After a threshold adjustment, it was converted to a BW indexed, scaled to its 16X96 original stitch and row count, and then saved in 100% magnification result for the possible electronic download.

The published repeat is intended for use on Silver Reed knitting machines, for using it on Brother machines, the initial 2 blank rows are shifted to the top of the pattern design.
On the far left below is the first BW processed single repeat isolated from its source. To its right, it has been adjusted so the first row is a preselection row for the lace pattern, and the full repeat ends with blank rows (Brother KM characteristic). The latter in turn was saved as an image for download.
Since the leaves change direction in the way they lean, the spacing between each pattern swing in the repeat is actually 3 all blank rows, not the “standard” 2, including at the top.
The bottom half begins with the first row resulting in transfers to the left, while after the first 3 knit rows the transfers will begin to the right.  The plan was for me to use Ayab for knitting a proof of concept swatch.  In order to achieve that, the full repeat is first flipped horizontally (ayab will auto mirror it,  so starting with it this way it will be in the correct orientation when knitting). The mirrored repeat may be used in unaltered machines as is with LC operating from the right, with KC operating from the left (not possible in ayab without adjustments). The full repeat consists of 16+14+18+16+14+18= 96 passes of the lace carriage, for every 12 rows knit. My sample was programmed horizontally for 3 full repeats, the width of my planned swatch. I added one additional needle in work on each side, with the LC end needle selection canceled, allowing for the full pattern as programmed with a single stitch all knit border on either side A tightly twisted cotton yarn did best in terms of handling the multiple transfers and not resulting in split stitches or breaking. I had occasional selection errors, seen in the center panel at the top of each repeat (my common experience with the interface), but the repeat itself appears to be sound. Lace repeats that have even numbers of rows for both and LC transfer and knit ones are easy to follow. Punchcards are also easily annotated and if knitting is interrupted needle selection is easy to return to or restore if necessary. In electronics, there may not be any memo to indicate row #  location for each carriage pass in the pattern, or when to switch carriages. Because in this instance there are so many transfers (some of the multiple stitches) between knit rows and dropped stitches are best corrected as noticed during knitting if possible, I created a “cheat sheet” of sorts to help keep track of actions. Each block outlined in red here represents one full repeat, read from the bottom-up, with blue borders at the center and red at the end of each half sequence. A visual check at the end of each segment’s # of rows in the series is well worth it to prevent unnoticed runaway dropped stitches and large holes. A check-in box next to # could indicate the completion of transfers. and a number added manually in that same row for that sequence, record the row on which knitting was interrupted ie. stopping on row 8 out of 16 to fix dropped stitches would be a reminder that 8 more LC passes are required before the next visual check. 

9/23/18 In now have been experimenting on a 930, where each pass of the LC is actually tracked, akin to following numbers on a punchcard.  Built-in patterns also offer a memo window, which will alert the knitter as to when knit rows are due In testing the pattern with img2track I found the LC passes are still counted, but the memo window is absent upon download. I generated a chart in Mac Numbers, reads from the top-down, expanding on the one above. It illustrates the number of LC passes (left column) required to produce any significant length of fabric.  Patterns such as these are not for the faint of heart and require a friendly yarn. 2168 passes of the LC (33 full repeats, outlined in green; red line separates half repeats) are accompanied by 396 rows of “actual” knitting. In actual knitting, the pattern advances from row 1 to 96, and back to 1 again. A check-off list can be much simpler if one is desired. The numbers on left appear in the LC window in a 930, when reached 2 rows are knit with the KC. The numbers at the top reflect completed repeats. Boxes can be checked moving to the right as those rows are completed Another option is to download the pattern in img2track, and then enter memo information prior to knitting it. Two youtube videos that show how to enter memos in machine models that allow it, 930 included  https://www.youtube.com/watch?v=S0tXNT76v10    and  https://www.youtube.com/watch?v=nR8MheT5Bao. The number 2 may be entered after numbers on the left appear in the LC passes count window, and provide an easy guideline to follow. And this is what testing lace patterns can look like. In this instance, a tighter stitch tension, a bit of change in weight, and visually checking after each row of transfers brought me some success. This is not a stitch pattern that lends itself to easy “repairs”. A more successful sample knit also on the 930 using the shared repeat as given, knit in wool-silk 2/18

Numbers to GIMP to create images for electronic download

I am a member of a few Facebook groups, recently joined the img2track one out of curiosity, and wanting to explore the possibilities of an interface other than an Ayab/910 from a kit, which has proven to be of limited use to me. I have been charting original patterns and color separations for years, first in Excel and occasionally and now exclusively using Mac Numbers. Up to last December, entering designs for knitting on my 910 was limited to filling in squares carefully one at a time or small blocks and lines on mylar sheets in order to knit the repeats designed in charts in either program. Working with small, individual repeats and filling cells one at a time or in limited groups in GIMP to create duplicate pattern downloads was an easy transition out of sheer habit. A FB group member, Julie Haveland Beer shared a file on how to Convert Mosaic Knitting Chart to KM Skip Stitch Diagram (shared with her permission) that sparked a light bulb moment. I began to explore using the method in her share on files available in other printed materials and punchcard collections, wondering about those lace cards with so few holes that can go awry when building from scratch in order to download. Often I use Scanner pro on my phone (rather than a full-size scanner), save images in black and white, share them via photos, and open them up on my Mac for further editing. The full-size scanner saves of 60X150 patterns may be found at the bottom of the post.

The first repeat was from

I happen to own a hard copy. The book offers endless repeats that might be adapted for knitting 2 color fabrics (or more with experimentation in some instances). They are categorized by height and width, so even punchcard owners can find whole pages of workable repeats. Another group member shared the link to the Compendium for online browsing https://archive.org/details/dictionaryofweav00poss

I have written several previous posts on using GIMP, including the use of the tiling option to visualize how groups of repeats line up prior to any actual knitting. The enlarged, “original” gridded image below would be the final repeat, reduced in size, grid gone, made ready for download in required image format.
A chart from my blog: the image is converted to B/W, then scaled to stitch and row proportions with just a few keystrokes 

From self-drawn mylar, with a subsequent one-pixel correction From colored repeats in Brother electronic collections: with some color adjustment after a first attempt that required some clean up of pixels, the conversion and scaling are easily achieved. The originals were designed on a rectangular grid, within blocks defined 6 wide by 10 tall the repeat tiled, for an added visual check Another Brother published in color repeat, scanned in B/W, imported directly into Gimp, mode converted to indexed, then the image was scaled to the size of the original illustrated repeat 34X36Check the scaled repeat on a grid for any missing pixels against the original

From a Brother electronic lace publication a simple BW bitmap conversion followed by scaling (60X120 repeat). The appearance of difference in width is due to the fact that the published image is on a rectangular grid, the bitmapped on a square one

If the electronic published repeat appears to have the core of the cells outlined clearly in white something to try: reduce to indexed BW, use bucketful to remove as many gridlines as possible, scale to appropriate repeat (24X48), edit the results A “straightforward” conversion for a repeat from a scanned punchcard with its darkest black line removed

and one from a BW punchcard reference pub

My last post on working with numbers to create knit charts includes info on creating tables, working with cells, keyboard commands, and more

using the combined programs: Things got more complicated again when I tried to work with a lace repeat from an electronic pattern book. The straightforward method resulted in an unworkable image. Part of the problem may result from varied densities of lines in the original, its cells not being fully filled in (ie dots in squares or rectangles), and illustration with units in a rectangular rather than square format, so they do not scale properly in a ratio of 1 pixel per row and stitch. After isolating the repeat, I for this repeat I entered it in numbers with the plan to superimpose a table grid over the repeat and fill in squares/cells where needed. Cell borders may be created in varied thicknesses and colors, and are easily changed or removed altogether. Having a red cell border to superimpose on the image made the process significantly easier for me. In the middle section the red border is switched to a significantly lighter one, and lining up the repeat beside the images helps one visually check for any errors. In the bottom row, the image is shown magnified after scaling, gridded in the magnified version again to check the repeat against the original.

Another lace image with table cell margins adjusted, and a reminder that borders may be in any configuration or color that makes it visually easier for you to proceed with filling in cells that correspond to black squares in the original image

The steps in progress, with the processed image ready to knit, shown in magnified, gridded final GIMP scaled repeat on far right. With a bit of familiarity with both programs, this process is far faster than any counting and filling in of pixels one at a time

This lace card was not cautiously cropped at the top and bottom edges, the final repeat when scaled is shown first, with obvious errors, but workable when done “the long way” from the same image or hand-edited

Taking the time for a more careful crop for another card and easy peasy: crop, open in GIMP, convert to bitmapped BW image, scale to stitch and row count of the original repeat (in this instance 24X56), verify gridded by GIMP in magnified image version, then save for download in reduced size

GIMP magnified and gridded final repeat above on left, one obtained working the “long way” between programs to its right Conversions issues may happen also when there are large areas of black squares or working with color adjustments or with the option to “photocopy” in GIMP in images that do not translate cleanly Working with repeats that do not convert easily using both programs: the greater the number of squares or dots, the slower the process, but ultimately faster than counting then and entering them one at a time. In Numbers, create a table that will be superimposed onto the desired repeat. I like to work in cells that are 24 X 24 points. Columns are marked in letters, so 24 is 2 letters short of the full # of letters in the alphabet (X), and row counts are numbered top down on left and easily adjusted. Lace repeats would be the easiest to translate, as they are likely to have the lowest number of cells that will require to be filled in. The cell borders may be created in any color. To my eye, the red grid made it easier for me to view its lines when superimposed on the black image. The BW center image was then dragged/dropped into the numbers sheet. Checking via the table format arrange option, the table was shown to be 553 X 1440. The image arrange option showed my black and white image to be adjusted visually by me using the corner handles to 496 to 1440. On the far right, the BW image is in turn adjusted to match point values for the table. Check your typing, adjust accordingly. Here my width on right is actually 3 points off.

Drag and position table onto a BW image. Use image format arrange to move the image to the back of the table (box to left below “Style”). Magnify screen to easier working view by adjusting the zoom. It may be helpful to alter some row heights or column widths to get a cleaner view and matching cells to be filled into dots (center). Click on any row or column, adjust by in turn clicking on up or down arrows that correspond to their respective size. Using command-click and color fill options, cell fill on top of the black dots. When done, or to check periodically, the table may be slid off the image and back on if needed. With the table completed, if any columns or rows have been altered in with or height, choose from the menu to distribute rows and columns evenly, restoring all square units.

Change border selection to light, thinner color, capture image and save as png. Load image in GIMP, convert to BW bitmap, scale to 24 by 60, save in downloadable format. Results are magnified in GIMP final images on the right. Showing grid allows an added visual check if preferred, against the original repeat. The final repeat tiled, as opposed to punchcard repeat tiled helped me see one missing square I found bothersome, an easy edit the culprit marked in red

The easiest conversion of all? a full-page factory mylar sheet. Here is one for lace with a simple adjustment of sharpness and contrast, magnified, and with superimposed rectangular grid after converting to BW bitmap for saving, to then discover that the blue grid disappears in a quick mode change to indexed in this factory mylar. The images on the far right are again the magnified scaled image and shown with a superimposed rectangular grid to check match against the original crop

Rethinking those dark cards: this is a partial repeat grabbed from Pinterest, the image was loaded into GIMP, color inverted, the threshold was adjusted while in RGB mode. The adjoining 2 images show the magnified, scaled, indexed image and its color reverse. When working in RGB mode choose color invert, and when working in indexed mode, choose value invert for color reversal of the image and its ground. Other image adjustments may require toggling between the 2 modes. The bottom pair of images indicate menu location for adjusting grid size and color, and the magnified, scaled image now with a GIMP single-pixel grid is also shown
This method, however, did not work for the flower? thread lace motif (partial repeat) or the FI repeat. That said in the days of glitched knits, perhaps executed in DBJ accidents such as this could make for interesting experiments or transitions. Here we have the original not planned result, followed by some flipping horizontally and vertically, then resized. There usually is no right or wrong, and it is important to find one’s own voice and the tools required to express it.

my favorite glitch textile artist: Phillip Stearns

for more on gimp editing see post

4/15/19 I have always been curious about weaving drafts and patterns being translated to knitting ones. I wrote a post on some of the basic possibilities in 2015, in my Excel days. Lately, I have come across many tempting charts shared on Pinterest from many sources. Some are more difficult than others to translate cleanly. Having a periodic leaf obsession, I came across this chart, which also will show some of the issues found in mesh grounds, thread lace, and other fabrics when there are regularly spotted grounds. 

I found the easiest way to work with the repeat was to overlay the table over the image using a much thicker cell border. The repeat was isolated, its colors reduced to black and white out of habit. Adjustments were made to the image eliminating aspect constraints, and it was laid under the grid to the closest visual match for stitch and row units cell size. Command select makes quick work of filling in pattern cells. When done, the table border was selected and rendered in a much lighter outline, the captured final image was saved, opened in GIMP (insured it was indexed), scaled to 38X50 pixels, and produced something in theory now knittable. Tiling is as always a good test to see if the final repeat meets your expectations prior to knitting and offers the opportunity for any other adjustments with the use of the grid and magnification even easier approach: use the same grid method on the original, in the original color isolated repeat. The table may be shifted slightly in its front position as one advances through the repeat, filling in cell content. another in progress repeat and its tiled BW counterpart using this method Luminescence is an online weaving program developed by Andrew Glassner. There are ample instructions and help files on site with regards to weaving. A related post, updated with information on processing images using a combination of Mac Numbers and Gimp, beginning with this draft Back in 2011, I had quite a lace obsession. One of the shawls I produced is shown below in one color on a blocking board, and in a completed other
The knitting took place in my mylar on 910 days and I still recall the tenacity it took to reproduce the lace pattern accurately from a small image in a publication, to a repeat 150 rows in height and 35 wide on the mylar. The original lace pattern was part of a series of motifs used in a lace shawl published by Susanna Lewis in issue # 5 p 43of Macknit, a short-lived machine knitting magazine. I now used the method illustrated with the woven leaf above. A thick cell border table was laid in front of a scaled scanned image of the original repeat, filling in cells, and then using the image grabbed from numbers in gimp to produce the final BW .bmps for download via img2track to my 930. Once I realized that the original image grabbed from numbers needed to be large enough to produce a clean scaled .bmp in gimp and broke the pattern into 3 segments 50 high each to accommodate the screen size of the Mac and an easy to count grab, within minutes I had my lace pattern for download subsequent proof of concept swatch was easier and quicker to produce as well now that I have a much better understanding of how lace transfers work, it was not quite centered, but appears to be correct

A bit on method:
Cell size minimum 24X24, at this size I was able to grab 50 rows at one time
Colored Border 6- 8points when filling in individual cells
Zoom 75%
Fill in cells with black
Change the cell border to 1 point dotted
Screengrab desired repeat as cleanly as possible, this makes a difference with straggler dots
Open screen grab in gimp, trim if necessary, convert to mode indexed 1-bit palette
Image scale to grabbed a repeat cell count. On occasion one of the 2 numbers may be off by one or 2 pixels, can be rounded off by breaking the chain symbol used for keeping aspect ratio constraints
If there are stragglers they can easily be edited with side by side comparison. There may be fewer with larger grabs. The method worked seamlessly for me yesterday, today I am getting extra black cells. Comparing with the screengrab and editing at 800 to 1000 X with grid, snap to grid preferences will make for a quick edit, still ever so much faster than drawing on mylar.

“straggler” illustrations for clean up in GIMP prior to saving for download

 

Charting knits using Mac Numbers 2

From 2012, Numbers 3.2.2: printing graph paper to desired cell dimensions: I chose to change preference for rulers to point units (options are for centimeters, inches, and points). Online conversion between units of measurement and PostScript points may be calculated (if needed) using calculators ie.
http://www.unitconversion.org/unit_converter/typography.html

default cell size in cm and points

Click on the table icon at top of your document screen, to right of function icon; select first choice on left, second row

a place to start

Uncheck alternating rows on the sidebar at right

Click anywhere on the screen, use command all to select all table cells. Choose row and column size, typing in your desired values or using arrows provided, hit return.

Click anywhere on the table to get additional markings to appear again. With your mouse, grab and drag the Add or remove rows and columns button symbol on the bottom right and all units on the sheet will be resized to displayed measurements

as you do so you will also have the benefit of viewing the number of rows and columns in your document.

For thicker, darker, or even differed colored and types of lines changes are easily made working with borders menus

Clicking on any cell leaves only your graph; selecting print from your file menu prints exactly what appears as the sheet number chosen, and /or have saved; additional adjustment options are offered on right

Click on the white part of your sheet, only your chart will be viewable and ready for printing. If a PDF is desired, choose Export to -> PDF from the file menu.

The last online manual for numbers 09 is available here. The program has changed significantly in appearance and in some of its functions since then.

I have been exploring numbers out of necessity since upgrading my Mac to the latest OS, thus losing availability to Office, and therefore to Excel. I recently published a post using Numbers for color separations in knits and decided to attempt to explore the program further. Here I am reviewing and sharing some of the process and information I now use in creating my blog’s knit charts. There is no recent, full manual for the program.

The format bar that may be familiar to users of older versions 

 

the Graphic inspector 

Tips immediately below are extracted from Online apple support  Numbers 5.0.   

A list of keyboard shortcuts edited by me for use with colored cells

“Undo” restores the previous state, may be used multiple times to reverse several steps. Redo will cancel it. The program autosaves. The option “revert changes” when closing the program erases all changes since its previous launch session. “Revert to” under file menu offers an opportunity to browse previous saves and restore them, similar to using the time machine in older versions of the program and Mac OS.

Frequently there are more options for achieving any desired result.

Building a knit chart: choose a default table from

Use format table in

  1. In the Format page1image1768000 sidebar to the right of the document to change features such as table name, headers, footers, as well as colors, and row and column size,

or click anywhere in table and select all  (Command A), choose no fill option on right to remove any default colors
Choose a border color and line weight. If accustomed to working with black as a color in your chart building, starting off with a colored border will make the black cells easier to count. The change may be made at any stage of the design

Determine column and row size using format cell menu on the sidebar at right. I tend to work in cell size 24-29 pt square shapes. These values may be easily adapted if one chooses to draw in knit proportioned cells for more closely approaching gauge or estimating elongation in fabrics such as DBJ. Border colors may be also be adjusted or changed at any point, globally,  for single lines, or to outline blocks of cells. Clicking on a column tab “letter” and dragging its border on one side or the other will change its width, and the new point value is visible on a shape with a black ground while doing so.  Top or bottom drag a “number” in the tab for rows at left for column height changes and viewing the changing value display. Undo will revert the change.

Review for basics for enlarging the table with cells with no fills: reference tab numbers on left may be used to refer to rows. Reference tab letters at the top may be used to refer to columns. Drag the table handle the Table handle to move the table. Click the column handle the Add Column button to add one column, drag it to add multiple columns. Click the row handle the Add Row button to add one row, drag it to add multiple rows. It is not necessary to press shift while dragging either symbol for multiple adds. Drag the column and row handle the Add or remove rows and columns button to the right to add columns, down for rows, and diagonally to add columns and rows at the same time. Reference tabs are active while the chart is being worked on. They disappear if any area outside the table is clicked on. Creating a chart initially larger than the planned design offers a larger field to “draw on” to start with. 

To draw shapes in color: click on a cell, choose your color 1 from the menu on right by clicking on the rectangle to the right of “fill”

To copy cells within a table, or to another table, drag the selected cells while holding down the option key. You can also copy cells by selecting them, choosing Edit > Copy (Command C), selecting destination cells, and then choosing Edit > Paste (Command V). You can also paste a cell€™s content into multiple cells, which don€™t have to be adjacent to the copied cell or to each other. After copying a cell, select the destination cells and choose Edit > Paste. The cell€™s contents are copied to all the destination cells, in the same or another table, replacing any existing content. An alternative way to draw motifs in different colors: holding down command key select cells that will compose the desired shape

choose the current fill color again to fill the outlined areas

adding a second color: click on a cell, choose the second fill color

hold down command, select cells for a new shape

color fill

repeat with color 3, and continue on

Not enough columns or rows for your motif?  Click on the Add Column buttontop right or on the the Add Row buttonbottom left will copy and add the previous column or row including content to clear unwanted filled cells in the added field, select column or row from tab reference letters (columns) or numbers (rows), choose “fill” as no fill

To insert multiple rows or columns at once: Anywhere in the table, select a number of rows or columns equal to the number of rows or columns you want to insert, “click the arrow” next to one of the selected row numbers or column letters, then choose Add Rows Above or Add Rows Below (or Add Columns Before or Add Columns After). The arrows are visible as you hover or click in either tab, seen more easily when working in larger magnification, and often clicked on while unaware of doing so in lower magnifications 

Alternately, click on table and in turn click and drag the Add or remove rows and columns buttonat the bottom right up, down, left or right for further adjustments to the total number of available cells,or simply repeat the fill in the selected column or row along with creating the added cells, and select areas to remove any unwanted color. In some instances, the added colored cells could serve as a deliberate design feature

Adding columns and rows above or below and columns before or after using the table menu. Options are greyed out until a row or column is selected. 

options also appear when you click on the arrow in the row or column reference tabs

Adding specific rows above or below can help scale coordinated designs. To add rows after a particular row, make sure the bottom row selected is the one after which you want the new rows added; to add rows before a particular row, make sure the top row selected is the one before which you want the new rows added. Then choose Table > Add Rows Above or Table > Add Rows Below,

or use keyboard shortcuts to add a row above a selected cell, press Option-Up Arrow. To add a row below a selected cell, press Option-Down Arrow. To add a row at the end of the table, press Return while the last cell is selected. To add a column after a selected cell, press Option-Right Arrow. To add a column before a selected cell, press Option-Left Arrow. To add columns after a particular column, make sure the rightmost column selected is the one after which you want the new columns added; to add columns before a particular column, make sure the leftmost column selected is the one before which you want the new columns added. Then choose one of the commands above. You can also use the Tab key to add a column to the right side of the table.

To delete a single row or column, hold the pointer over the row or column reference tab to see the menu arrow, and then choose Delete Row or Delete Column from the pop-up menu.
To delete several adjacent rows or columns, select the rows or columns and then choose Delete Selected Rows or Delete Selected Columns from the pop-up menu of a selected row€™s or column€™s reference tab.
To delete empty rows, drag the lower-left Row handle  the Add Row button up or drag the lower-right Column handle the Add or remove rows and columns buttonup.
To remove rows with content, hold down the Option key while dragging.
To delete empty columns, drag the upper-right Column handle on the Add Column buttoninward.
To remove columns with content, hold down the Option key while dragging.
Moving a cell or groups of cells: select and choose group by using cell handles or commands, immediately click on the same selection again, and drag it to a new position within the same table. Moving the selection outside the table, onto a blank portion of the sheet creates a new table.

Having a large table area to work on allows for copying and pasting repeats in different configurations. 

Added ways of working with cell groups: to select adjacent table cells, select a single cell, and then hold down the Shift key as you select adjacent cells. You can also click a cell, press, and then drag its handles through a range of cells. As seen above, to select nonadjacent table cells, hold down the Command key as you select cells. Continue to hold the key, and use Command-click to deselect any cell in the group.

Adding, copying, and pasting tables or portions of them. Clicking on the + beside sheet # will create a new default table, on a new sheet, a new sheet of “graph paper”.

Tables and their data may be copied and pasted from one sheet onto another, or on the same sheet. To add a new table in the same sheet from available templates click the Table button in the toolbar, then click a table or drag one to the sheet. Reviewing process once more: Move the table: Click the table, then drag the Table handle in its top-left corner. Add or remove rows: Click the table, then drag the Add Row button in its bottom-left corner down or up. Resize the table: Click the table, click the Table handle in its top-left corner, then shift-drag the white square in its bottom-right corner to resize the table proportionally. Change the alternating row color setting: Click the table; in the Format  sidebar, click the Table tab; then deselect or select Alternating Row Color. (To choose a different color, click the color well.). Change the look of the new table: Click the table, then use the controls in the Table tab of the sidebar to make changes, such as adding a table outline or changing the table font size. To delete the table click the table, click the table handle in its top-left corner, then press Delete on your keyboard. An alternative way to create a new table matching presets is to copy a blank segment of one of your existing tables and paste them, adding and subtracting more blank squares, or even to copy a full table with color designs, and simply remove color fill after pasting.

Selecting a portion of a table that contains graphics and choosing copy and paste will reproduce the selected portion as a new table, usually at the upper left of the sheet, sometimes on top of a preexisting table.  When working on large charts, the pasted table may be “hard to find”. Reducing magnification to 25% sometimes makes that easier, since larger sheet area then comes into view. Clicking on any tables and dragging on the the table handle at their upper left allows one to move the contents to its desired location.

Fine-tuning table size and positions may also be achieved by changing values in the size and position sidebar format options. Click on arrows for default size moves, or click in respective value boxes and type in the desired number, hit return 

Some of my tables have table 1 above the graphics, some not. That can be changed by clicking on the table name box in the format table menu 

or click the table, Control-click the row number for row 1, then choose Hide Table Name or Show Table NameTriple-click the name at the top of the table, then type a new name to rename it. Keeping a “name” helps track versions such as when working in color separations, where a whole table is repeated and altered in a series of steps while preserving the previous one. Below a table segment is selected, copied and pasted as a new table. The new table is moved into a position next to the original. To combine the tables in order to create a new design, choose arrange from the format menu. In this instance, I chose to position the new table by clicking on it and selecting the back paste option. Once you click on a blank part of the sheet, the table tabs will disappear. The tables are visually merged, but in fact remain separate tables, each of which can be moved, resized, added to, and otherwise altered. 

It is also possible when working on 2 tables to select and cut out a segment or more. Below, the table with the cut-out window is moved onto its unaltered table twin and shifted up (note numbers on right, and red border segments) 

A different “table” with the same cell dimensions, may also be dragged and placed under (or over) the “cut” portion of the first. My placement here is slightly off intentionally to show table placements for under/ in back  

and placement over/ in front  

To screen grab tables with row, column tabs, and corner bullet markings click on any individual table cell (note the outlined cell with handle markings upper left and lower right), and use shift-command-4 to select area for saving.  For a multiple-table grouping, hold the shift key while clicking anywhere in any single cell contents of multiple tables, and while still holding shift, add command-4 commands, select and save. Clicking anywhere outside the tables on the “sheet” results in tabs and bullets disappearing. Click on any cell in any table again, to move it, or make any other adjustments needed.

A helpful yellow dot: for sequential numbering in any row or column, fill in a minimum of 2 with number values ie 1, 2, 3, select all the numbered cells, a yellow dot will appear on the right click on it and drag across the row of cells you wish to number and  doneFor numbering in the opposite direction, simply begin numbering on the right in reverse order for at least 2 cells, and use the same technique. For vertical numbering, once again, use the same principle at the top or bottom of the column you wish to number.
Multiple numbers, symbols, or letters in repeat (wish I knew of this feature or its possible availability in my earlier charting)Any table may be adjusted to accommodate adding text, shapes, or to expand on instructions.  Working with shapes merits its own, separate discussion.

My favorite font, used in most of my charts that begin to address specific fabrics such as lace by adding symbols,  is no longer available for distribution. For more on symbols and fonts see post

If colored cells are in use and text or symbols are added to any such cell, the ground color may be lost. If a color is added to that cell after the text/symbol entry ie by copy and paste of a colored cell, the text is lost. Arrange behind from the format menu does not work in this instance. The quickest method is to use the command key, click on any cell containing only the chosen color you wish to use behind the text, drag and drop selected content onto text, and the color will appear behind it.
Another method is to use command key, click on the chosen colored cell,  use format menu to choose color fill, click on the original cell and the one you now wish to color, finally choose color fill from the format menu again

Online published shortcuts for using the program with downloadable as PDF 

 

A Brother 910_ Ayab diary/ EMS kit

This is a work in progress post. I have now edited and included its previous version so the most recent observations appear first, the oldest last.

9/8/18 I have received a replacement unit from EMS. I got this far testing a large scale pattern, no fault of the program at my stopping point. I did not notice until I got across the last pattern row that I had actually knit with both strands of yarn. Rather than try to fix the issue, I decided to scrap off. This gave me a chance to test new yarns. I had never used chenille in DBJ on Passap, it sheds too much, resulting in error messages. I like to have my scarves at least 60 inches in length, and this combo looks as though it would reach that length when completed. I also did a bit more editing of the repeat as shown here. We shall see if the equipment and I both last to a whole 1200 rows or so in one sitting anytime soon 😉

6/25/18  the kit apparently has now gone from out of stock to officially no longer in production 

5/28/18 replacement kit never received, it’s back to mylars for me to actually try to get any significant knitting done 

4/27/18 I have been able to develop some fabrics using two knit carriages selecting needles from opposite sides, though the lace carriage will not select from the right if the knit carriage is also selecting from the left. The posts include altering a knit carriage to use as the second one to select needles as an alternative to changing ribber settings between normal and pattern knitting, and addition to posting on combining KC patterning with racking

I had been told my kit would be replaced due to persistent patterning error issues. Sales are presently on hold while the hardware is reviewed, and work is being done on a new version of the software, so any changes in status are to be determined.

3/ 31/ 18 At present there is no English text manual for using the software or a quick start guide. I am sharing some of the differences and similarities in actions I have noted between the unaltered 910 and those of the hack, beginning with settings, and including a few tidbits gleaned from support as I encountered patterning problems. They may be of interest to those making the transition after previous knitting experience and familiarity with the machine, or to anyone curious about the program and some of its features and differences.

Yellow text in this first image from a publication on the 910 indicates matching functions I have identified so far in ayab software.

the full illustration from the 910 manualactions on the unaltered 910

When the pattern selector is down, the pattern is centered on green #1 (right of  0). This means if the pattern is an even number, say 24 stitches, then the pattern limits are green 12 and yellow 12. If the pattern is an odd number of stitches the pattern limits are yellow 12 and green 13, the center being green #1. With an odd number of needles, Ayab places the larger number of needles on the left, its orange (yellow) side.

AYAB

I purchased my hardware kit (now off the market) from the developer : to purchase , wiki , interface , install. Online discussion groups:  Ravelry , Facebook, and GitHub.

At present, there is no cover readily available for the machine once the unit is installed, so the left side of the main bed remains exposed.

Though beeps heard upon preparing to preselect the first row from left to right are described as a triple beep, I hear them as a triple set of multiple beeps with pauses between. Not taking the time to “hear” them all will result in patterning errors from the get-go. Be sure to hear the beep and see the flashing of the unit before reversing carriage direction. Clear the left turn mark at least periodically while knitting. If you have experience with any production knitting on the unaltered machine you may feel the knitting speed is slowed when using the software and cable for downloading each row as opposed to that with which the mylar scanner accomplished the same task.

Ayab can be set for an infinite repeat in length, the function was automatic on the mylar unless one made the choice to stop at any point. A single repeat on the mylar was enough to program across the width of the needle bed, with ayab the full width of the pattern must be programmed, so designs need to be tiled accordingly.

Installation of software can be achingly slow on Mac desktop (I am using High Sierra OS). SiLabsUSBDriver  is also required. Security settings need to be checked/changed even if no warning is given by the computer leading one to assume there have been no issues with the download or the install. The driver will reside in the library/ extensions.

The hardware install is fairly straightforward.

The USB connection needs to be made prior to launching the software for the port to be recognized. If port questions come up, click the “Refresh” button on the AYAB screen. When things are working correctly, you should be able to see a port name from the pop-up menu. The plug-in power supply supplies power only to the needle selection.

The popping noise or clunk is heard usually but not always when you cancel AYAB and restart and is produced by the solenoids. I have been reassured it “does no harm” by support.

The launcher box remains open throughout knitting.

To start knitting:
1. Load your pattern in the width of the planned repeat
2. Set all the AYAB settings at default (2-color, start at row 1, single, center). Check infinite repeat if you want to knit more than one vertical repeat
3. Knit carriage is on the left, outside the turn mark
4. In the AYAB software, Configure/Knit
5. Wait until the software says Please Init carriage at bottom of the screen
6. Bring the carriage across the left turn mark and stop before crossing any needles, wait for the triple set of beeps.
8. Continue across the first row and stop, wait for flash and beep, then proceed with movements to and from each side, again waiting for flash and beep that indicate each row download is complete.

If knitting a repeat in single height, when you are one row ahead of the last selection the row numbers disappear as “Image Transmission is finished. Please knit until you hear the double-beep sound”. The marker on the image jumps down to the beginning. You knit across and it does the selection for the last row and gives the long beep sound. Knit one more row to actually knit that selection. When all needles are selected to B, you cancel your settings and you’re done. 

In some instances clearing both turns marks seems to help avoid errors and ensure consistent patterning. Beware of moving the carriage back and forth for any reason, ie to fix a yarn loop, dropped stitch, etc. The movements in my experience have been counted as rows, resulting in patterning errors as would happen when using a punchcard machine. If working on a desktop as opposed to a nearby laptop you may be missing any visual cues for row advancement provided by the ayab screen.

The image displayed on the screen may be magnified and reduced to fixed amounts, but at present, there are no programmable cues as might have been used on mylar ie. for color changes, lace vs knit carriage actions, etc.

When exploring the menus, creating an easy to view repeat helps to sort out available actions

The single setting is used for all single bed fabrics. The row numbering starts from 1, not 0, and focuses consistently on the row whose pattern is being selected, not the row being knitted; design row start line placement

start needle design stitch position on needle bed 

single design alignment test: left, center, right of the same repeat on an alternate start stop needle configuration 

As mentioned, with an odd number of needles, Ayab places the larger number of needles on the left, its orange (yellow) side. It also automatically mirrors all patterns, so lettering and images appear on the knit side as drawn. The mirroring, however,  is a problem with lace. If working from an established pattern, the lace repeat must be mirrored again either before loading the pattern or prior to knitting it or lace transfers will be made in the wrong direction. It is possible to operate the LC from the right side using Ayab, but if  knit carriage is also set to selecting needles ie. if set to slip stitch, and is used in combination with the lace carriage, the LC will not select when operated from the right, and the pattern will not advance properly (documented by others as well).

I used to constantly use 2 knit carriages in a lot of my accessories. At this point, that function is not possible due to patterning errors or loss of patterning when the second carriage operates from the right.

The first preselection row in Ayab is made from left to right. For any pattern that requires a start from right to left, ie one with color changes every 2 rows, there are 2 options. One is to place the design row start line at the very top row of the repeat. That row will be selected left to right, the first design row will then be preselected right to left, and the 2 color rotations using the color changer on the left can proceed accurately.  The other option is to shift the last row in the programmed repeat down to row 1 position prior to downloading the pattern and saving that as the working repeat.  I prefer the latter since it eliminates having to recall the change in the start line. An example of the shift is seen as applied to the automatically shaped lace trim

The ribber setting: a reminder, later color changers were also capable of being used on the bulky machine

Brother DBJ KRC setting including on the 910: white is the background (color 1), punched holes, black squares or pixels are considered contrast (color 2)

This is the KRC color separation described for DIY use on a punchcard machine: 

some of the possible backings (vertical striper requires extra steps)

Previous related posts: https://alessandrina.com/2015/04/18/a-simple-shape-an-exercise-in-dbj-brother-km/ and https://alessandrina.com/2017/10/26/dbj-and-color-separations-some-previous-posts-links/

AYAB color sequence is reversed from the Brother convention of white pixels being color #1, and black pixels being color #2. It chooses black as color #1, white as color #2. The first pass to the right is set up with the “black” yarn. The actual position in the color changer can vary depending on how the yarn is threaded in the mast. The first pass to the right preselects for the first row of black squares, which will be knit on the first pass from right to left. In one option, the ribber needs to knit the yarn in order to get the carriages threaded with yarn to the other side, the KC makes a free pass, with nothing knit. This is achieved by having the main bed set to slip <– –>, and the ribber to selection to be used in the remaining DBJ fabric. After knitting across and waiting for beep, knit back to color changer, the beep happens again as you reach the opposite side. Press the button to change yarn to “white” and continue in pattern, changing colors every 2 rows. Depending on your choice of start to the piece, another option may be to have the ribber set to slip as well on the first preselection row from left to right, thread the “black” with the carriages on the right, using it to knit that first design row, moving toward its empty slot in the yarn changer, where you will then pick up the “white”. Check cam settings on both carriages before moving back toward the right. Thinking of the pattern in terms of black and white and matching the sequence as described frees one from the factory KRC convention.

KC I or II may be used, needle arrangements can vary depending on the look one prefers on the edges. It is helpful to have some previous experience with ribber use and understanding of how stitches are formed. Patterning resulting from choices on end needle selection on either bed may be considered a boon or a distraction, at times even create a smaller, secondary pattern (arrows)

The circular setting: was intended for tubular fair isle, some of my experiments to produce other fabrics may be found in earlier posts. The ravelry group discussion on the topic including using the setting in knitting socks, with an extensive tutorial by Adrienne Hunter: https://www.ravelry.com/discuss/ayab/3346844/26-50#38

3/15/18 After more testing I have come to the conclusion that end needle selection cancellation on my 910 LC is working properly, but is not operative when I am working with my Ayab interface.

3/5/18 While working on a post on shaped lace edgings on Brother machines  I encountered 2 new issues. One appeared to be I was unable to restore end needle selection on my LC while sorting out the repeats. The other was that if 2 carriages are in use, the lace carriage will not select needles if operated from the right, while if is the only carriage selecting needles, it will work from either side. This is a property that is not isolated only to my set up.

2/28/18 I have continued to intermittently knit swatches on my hacked 910. The software continues to be a boon in terms of avoiding the mylar and producing test fabrics quickly. At one point it was suggested I flash the Arduino “go to the Tools menu, Load AYAB firmware. Choose 910, Uno, 0.9. It takes a few seconds to reload the firmware (the part of the program that’s in the actual Arduino.  The changes from 0.8 to 0.9 were minimal, but it’s best to make sure you are using the latest.  EMSL preflashes them in testing so it’s not normally necessary for the user to do it.” Mine had not been. Doing so has not changed any of the behaviors that make me reluctant to even attempt to knit anything other than short fabric tests.  The trick now has become to keep enough patience and distance to be able to not assume that any patterning issues or fabric inconsistency are due to the software and not my own inattention or faulty notes. A recent observation: if an odd number of needles are being used the rule is that the larger number will be on the left.

1/21/17 I have been reworking some of my previous posts to accommodate for the fact that Ayab preselects the first knit row only moving from left to right. After being contacted by a design school student in Europe with respect to creating specific designs in 2 color drop stitch using ayab, there is now a dedicated post on the topic. Nothing has changed in terms of my having reliable and consistent patterning for any significant knit lengths using Ayab. In addition, the knit carriage movements in the 910 when using the software now behave like the Brother punchcard knit carriages. Any change in movement in the opposite direction or jiggling of the KC for any reason can make the design advance pattern rows. This was never true for the unaltered 910 machines, which were wonderfully reliable if the knitting was interrupted, if carriage were moved outside the knit edges for any reason, did not need to clear end marks for any reason other than on the first row of knit, were able to preselect first row from either side, making patterns that required use of the color changer usable without design first row adjustments, and the list goes on. The Facebook group is an active one, and worth joining for anyone seeking more observations, advice, and inspiration.

1/7/18 Over the weekend it appears my software has now begun pre selecting  first with errors, and now correctly on that first pass from left to right, so I will now be reviewing any instructions I have posted this past month in case settings need to be changed for anyone trying to execute the same fabrics, beginning with  lace.

1/4/18 My Ayab software set up rows work this way: the first pass from left to right only gets the carriage to the right, selecting only first and last needle if change knob is set to KC I. The second pass from right to left preselects the first row of pattern. The third pass (from left to right), knits the first row of pattern, selects the second, and so on; the subsequent selection is correct, no rows of the design are skipped. It has been pointed out to me that this may be a unique feature to mine or one unreported by others. “First preselection row should occur on that first pass from left to right”. My posts on using the software are based on the first pattern row knitting from left to right, not right to left as would happen if the very first pass from left to right preselected for the first row of knitting. At this point in time, it is also not possible for the first preselection row to occur moving from right to left. This, in turn, needs adjustments if patterning needs to occur in 2-row sequences from the left ie. in knitting mosaics and mazes unless preselection happens from right to left,  a result of my version’s “quirk”. Since I also knit on an E6000 the first 2 rows feature to complete preselection for the first row of pattern is a familiar one, and from the beginning, I assumed it was an intentional feature in the Ayab software as well. It actually solves the problem if the first selection row needs to happen toward the color changer. Fixed starting sides can be problematic depending on the type of fabric being knit.  Lots of options to explore.

12/28/17: tuck lace meets hand technique 

12/25/17 my first try at lace: the LC is the one to select for transfers, the KC knits to complete the formation of stitches. Brother punchcards for lace usually begin with selection rows, end with 2 blank rows at their top. Using Ayab the repeats need to repeat across the width of the piece. One nice added feature is that when doing so, blank rows may be planned and left at both sides, creating a knit stitch border and eliminating the problem of paying attention as to whether end needles are selected or not, or what other measures to take. This fabric creates large eyelets, there will be 2 empty needles side by side for the duration. Some of the old pattern books referred to it as one of the “mock crochet” ones.

the resulting fabric, knit and purl sides

one more to try: a large diagonal eyelet lace combining lace and tuck 

1/22/18 swatches with preselection from left, similar results for shapes that are shaped with single row increments in height. Double height, the fabric creates tiny pintucks, not blisters as can begin to be seen at top of swatch; KC slip <—, ribber slip —>;

shapes as seen in test swatchverifying presence of pockets 

For a full post on quilting in one or 2 colors please see later post 

12/23/17 The “quilted” fabric produced below is different than the one achieved by specifically designed color separations, the fabric has an interesting blister like effect, the knit areas have more horizontal texture. Because of limitations due to the eventual needle selection errors, I am experiencing with the software, my swatches are limited in length or have interrupted patterns. My new repeat two of the “pockets” have beads dropped into them to highlight their location 

12/22/17: settings given below are for first preselection row from right to left, not for left to right,  testing out the waters with the circular settings, using the repeat. Please check later posts for reviewed content 

I tried to go for “quilting, but think that may require switching levers on the ribber, so to start with, this was knit in an every needle rib, with the ribber set to knit <—->, main bed set to slip —>, producing a fabric with very subtle pintucks, which may be more interesting in 2 colors
Quilting: KC slip <—, ribber slip —>

The pink and white swatch is in “drop stitch lace”,  was also knit using the circular setting. Instructions for color separations for fabric, how-tos, tools, tips, and samples may be found in my posts on the topic, with the same repeat used in https://alessandrina.com/2015/06/16/geometric-shapes-in-drop-stitch-lace-2-brother-km/ 

the image resulting from my own past color separation its purl side, turned sideways

Previous posts have covered manual color separations for fair isle, quilting 1, quilting2, and a summary of series on drop stitch lace. A later post on drop stitch lace using ayab .

One of the differences in using Ayab, is that knitting set up begins on the left, with first preselection row happening on the second carriage pass from right to left. This makes sense if the goal is to set up patterning for moving toward the color changer. Passap E6000 uses the SX/GX (2 Rows) for set up, with its color changer on the right. The knitter may set the carriages or locks for any chosen setting (knit for knit rows, slip if the extra 2 rows knit are not desired as part of the pattern or those suggested by console or other instructions). In the original state 910, the starting side is of no consequence as long as one is outside the set line, and preselection happens on a first, single pass. The same is true of preselection in the punchcard, one may start on either side. In some fabrics such as slip stitch worked holding techniques, or if the color changer is in use and making moves in even numbers of rows toward and away from it are required, starting side matters. The Ayab circular setting does the color separation for the fabrics above, but other cam and lever settings may need adjustment, based on sorting out what selected needles are doing when knitting starts. For the “quilted” swatch above the left part button on the KC, and the right one on the ribber were used. Sometimes the guide to color selection or cam settings is whether the first square in the imported image for download is black or white. With the loss of the built-in color reverse on a hacked machine, it is easy to work when swatching and testing to color reverse the repeat by using invert, available in the color menu, providing the alternative repeat. In Gimp the grid color may be adjusted as well if you choose to work in black and white as your starting palette. For the individual image, Image/ configure grid changes the preference for single use. 

12/19/17 I am continuing to really appreciate the speed and ease for sampling pattern ideas. That said, I  have also again experienced selection issues varying from lost selection to repetition of the same pattern row indefinitely, frequently after more than 50 rows are knit, and in spite of increasing attention being paid to beeps and flashes. Short pauses also seem to put the software into time out mode. I have not done enough knitting to evaluate whether moving the carriage past both turn marks with any frequency prevents those selection issues. Support is responsive, with new tools come new learning curves for everyone involved.

There is a popping noise /clunk that I have now learned is routine and  “likely from the solenoids being engaged or disengaged, when they’re first powered up, or released at the end.” It is a noise I have never heard in standard 910 use. I usually power down equipment when not in use, and have been told: “For the sake of longevity on the knitting machine, it’s probably better to err on the side of disconnecting the USB cable when you power down the machines.”

My present knitting efforts are to come up with some sort of variation of this fabric, published in an early Empisal Ribber Pattern Book, shared in a Facebook forum post.  I have used racking in a variety of experiments but never traveling over a MB pattern as in this instance. There is now a dedicated post on the topic 

12/17/17 I am brand new at using the system, my comments here are logging my personal experience and observation as I am learning a new tool, not intended as a guide. Please follow forums for advice from folks with more experience and knowledge.

The ayab interface from EMS is now up and running on my 910. The process was easy and straightforward in terms of hardware. Software install on the Mac is very slow initially, but the launcher operates quickly after that.  I am using the system connected to an iMac presently running OS 10.13.2. There initially were issues with port failure when attempting to use the program to download. No security warning was received when the driver download was completed, but rather, the image below, which I took at face value, so I did not immediately access the preferences security panel to make any changes thereIt took some sorting out with EMS support and finally accessing preferences security settings and “allowing” the install to solve the problem. Apparently, there may be some change in the message received within a half hour of the install. So, easy fix, check system preferences security settings regardless of pop up window even if lacking  familiar and obvious warnings such as

At present, there is no cover available to fit over the kit and its wires, so the left-hand side of the machine remains exposed. There is a row counter built into the software, but I tend to rely on the built-in on the 910. Any DIY cover should take clearing the row counter and the knit leader trippers into consideration. There is some conversation about 3D printed ones or even metal. Tiny detail: the kit comes with electrical zip ties to help secure the plastic shields on both sides of the board.  Clip the ends, and twist them so join sits either on top or under the interface, thus keeping them clear of KM parts, and, particularly, the belt drive on the left.

There are a series of beeps and flashes that indicate that the pattern row has indeed been downloaded and is ready to be knit. 910 mylar users are familiar with the sound coming from the reader as each row is scanned. Prior to using the Ayab system, I was initially concerned about beeps for each row adding to machine operating noise, since I am familiar with the Passap screech and at one point was also with the Studio electronic version. The Ayab beeps are actually on the soft side, and background noise or inattention may actually lead one to miss the cues. LED flashes occur in pairs indicating the row is ready to knit as well. Again, any cover may hide the light or soften the beeps, even more, making the cues available via the screen more essential.

The kit comes with a 3 ft. cable. I have rearranged placement of my machines to make using both the Croucher cable, switch box, and wincrea on the Passap, and the Ayab system on my 910. My initial wish was for a longer cable, which is possible to use. That said, there are several knit from screen clues that if you are operating the machine any distance from the computer get lost and become hard to see, including indicators for row numbers and the pattern advancement lines on your motif.

So far I have small FI samples and DBJ  samples. Ran into a problem after 60+ rows of each with mis patterning occurring, but that may well have been operator error. I have used my 910 for production accessories and was very familiar with a personal optimum speed. I believe I almost unconsciously with the initial samples, may have picked up speed and interfered with the accurate download of pattern rows. When I slowed down and was much more deliberate, waited for each flash and sound, a test got me to RC 110 with no issues before I quit for the day.

11/27/17 This punchcard was shared by someone trying to reproduce the implied fabric on their 910. It is intended to be used as a combination lace and weaving card, so on the punchcard machine, 2 carriages would be locked on the belt. If even number of passes are made with each carriage, there is the issue of the card not advancing each time when the opposite carriage makes its first pass. So far I have not been able to get this repeat to work for me as drawn, to produce results anything even resembling the “finished swatch” published photo. It did work for me using the LC carriage for 3 passes, releasing it, and following it by 2 rows knit with the KC set to tuck in both directions, a very different fabric. If the LC  is released after an odd number of rows, then technically when the KC is first in use,  the right to left and back to right selection is not interrupted, it is moving in the direction the LC carriage would have moved, and the punchcard row is not repeated. The first row with LC selects, second row transfers, selects next row. Third row transfers, selects every other needle for the first tuck row on the next pass of KC, and LC is released. The fabric then tucks for 2 rows as punched, on every other needle. The second tucked row is completed with KC on right. The first LC row has now been preselected, as the *LC heads back to the right (1) it transfers the selected needles, selects them again, but since they are now already empty, nothing happens to any yarn, and the next row of transfers is selected (2). The second set of transfers is made to the right (3) as the first tuck row is preselected. LC is removed. KC tucks for 2 rows (4, 5), selecting first LC transfer row with the second pass.* Repeat. The marks on the left should indicate carriage movements for each carriage, but they are off as well in my version of the fabric. My final repeats were for use on the 910 with a mylar.

the pattern book swatch image tuck swatch

Lace is a challenging enough fabric without adding weaving yarn floats, and definitely combining them requires a clear understanding of what the yarn is doing on the needle hooks as one progresses through the repeat. I will be starting a separate post reviewing card markings in punchcard pattern books, and translating them for electronic use. For further information please see post on 589

I have always been interested in machine knitting hacks and began sharing information from the internet on the topic as early as 2013. I own the 910 Brother model, and when the ayab hack first became available, assembling electronic components was beyond my skill and interest. I have a good supply of mylars, but have always knit more complex fabrics on my E6000, which has the Croucher cable and switch box for download to and from a Windows laptop, using Wincrea .  I had known a preassembled kit for the 910 hack was in development from a trip to CA, which included a visit to the Bay Area Machine Knitting Guild  back in April 2016.  A recent post on Ravelry alerted me to the fact that Ayab was “alive and well”, and that an assembled kit is now available and on the market. The hardware kit developer , to purchase  , wiki , interface , install . My understanding is that the software is still being developed in Germany.
Online discussion groups:  Ravelry , Facebook.  My compiled list of online pattern generators, hacks, free KM manuals, and more: 5435

I have purchased a kit and will share my experiences with it as time passes. In addition to bypassing the mylar use, the idea of having software that will render color separations that would normally have to be hand drawn for larger repeats than would be practical, or for complex fabrics, is an exciting one.

An artist whose work I admire, using the interface early on is Claire Williams , her tutorial  updated 2016 with DIY assembly of the original “kit”.

Double jacquard using punchcard machines

Each row of double jacquard consists of at least 2 rows of patterning, one with ground yarn, the other with contrast.
The rows knit per design row vary with the number of colors used in the design. The appearance of the designs and their backing vary based on settings used ie, tuck, slip, or normal knit, and their consistency or combinations in the same piece.
Punchcard knitters are not excluded from producing such fabrics, but the color separation is done by hand or using software, marking matching squares to pixels on the card, printing traceable templates, and then the cards are punched. The size of the repeat is less important in creating interesting knits than the choice of yarns, colors, and technique choices.
In early art-to-wear days, pre-electronic home knitting machines, large, non repetitive images were created by breaking down the large images into several vertical panels the width of the punchcard repeat plus seaming allowance. Upon completion, the panels were joined side by side to create the final image.
Ribber settings for DBJ apply across models in principle and may need adjustment depending on the age and brand of the machine.
If working on a bulky machine, consider using the ladder-back method.
The common method for the color separation suggested in instruction manuals for Japanese knitting machines is used in these samples.
The repeats for punchcards have a maximum width 24 stitches. Factors of 24 ie 2, 4, 6, 8 also apply.
Each group in the total 24 stitches in each design row is repeated in fixed locations across the needle bed.
A charted view of an initial design:
One design row of pattern requires 2 rows of punched holes in the in the card, each representing two carriage passes from and back to the color changer.
The step-by-step separation for the design on the left repeated across the 24-stitch card width follows.Helpful tools: on one blank card color each section of the card, representing color change sequences. This may be used later to check color separation.
Box the edge numbers in pairs, beginning with numbers 56 and 57, skip two rows to numbers 60 and the factory-marked row 1, the first visual row when the card is in the reader, and so on. as seen on the right.
This separation splits the first and second row of color 1 between the first and last row on the punchcard.

On a second blank card, prepare a master. The first row is left blank, then 2 rows are punched out, followed by 2 rows left blank, repeat, ending with a blank row. Again working upward, number each row you have punched out on the left-hand side starting with number 54, then 55-56, 57-58, etc, ending with a single row, 23. This will result in number markings matching both sides at the bottom of the card, below the #1 factory mark. My own master began on the left with the # 53. I also added corresponding design row numbers for each row on the far left. (1 and 2, 3 and 4, and so on). Written notes on right: an even number of rows need to be knit in each color, so in this method, the pattern must be an even number of rows in height, boxed numbers represent rows knit in ground color.

1: In this method, each color in each design row knits only once, reducing the elongation of the height to width aspect ratio in the knit.
The initial design is rendered in color, twice as tall.
A minimum of 36 rows are required for the card to advance properly in the reader.
Take a blank card to be marked with 2 colors, and put the master card on top, fastening the 2 cards together with snaps.
You can now mark holes to be punched. Copy the first 2 rows of color 2 on rows marked 54 and 55 (or 53 and 54 in my case), and repeat in pairs for the required height.
I like to mark the card to be punched with colored pencils that differ sharply for each color. They have the benefit of being erasable and can help with keeping each row distinct when punching.

When the completed repeat is marked, unfasten the snaps and move the card down by one row. You will now see the marks you have made through the top row of each set on the master card. Mark through each lower row any blank squares in the row above.

Again, after completing the repeat unfasten the snaps and slide the master up by 2 rows. The card will now be back to its original position, and up by one row. Now you will see the marks you have made on the blank card showing through the bottom of each row of the master card. Mark through each upper row on any square opposite the ones marked in the row below. After the repeat is completed, make certain to punch across 2 final rows for the card to create the overlaps for a continuous pattern, as with any other stitch type. Punch out all marks, and you are ready to knit. To check your design visually lay the finished card over the colored master, and correct any errors if noted. Your card is now ready to knit DBJ.
The first preselection row is from left to right with color 1, which will knit in pattern from right to left, moving toward the color changer where colors are changed every 2 rows. This color separation will not work for fabrics that require the same needle selections repeating for pairs of rows throughout.

2: A second master that may be used with the same approach, for a different type of color separation: This separation works with any number of rows. The design will be elongated X2 in height because each design row knits twice in each color, with 4 rows completing it.
The finished knit will be thicker as well, so use thinner yarns when working it. Draw shapes in colors that are chosen for clear contrast, not because they are to be used in the finished piece.
Here I am back to those triangles used in earlier posts. The choice of which color you begin with, whether in the separation or in the knit is ultimately up to you.With the masked card, the first row is marked on the very bottom of your new design, I began with the red, which would produce the equivalent of thisRemove the mask. Beginning with the second row from the bottom, mark any square not colored in the row below in a contrasting color  Punch all colored squares and you are ready to knit. I prefer to not rely on built-in elongation if I am making a garment or a long piece of knitting. If errors are made or correction of dropped stitches, loops, wrong color selection, etc. is required, unraveling rows is complicated enough without having to also sort out exactly where you need to be in relation to where the card did or did not advance. Black squares represent punched holes, a segment one separated by the red line in repeat width could be used on mylar or for electronic download.  3: Another master for the elongated design, advancing every row, numbers represent rows being filled in, beginning with odd in this orientation, and even with the card rotated for marking even # rows in color 2This is the same repeat, color-separated, and elongated X 2; proceed as with the directions above, but in this instance, each row in each color is marked twice. The expanded repeat:The first preselection row is made from right to left toward the color changer, where colors are changed every two rows.
I have used these images to illustrate color separations in far older posts.

The reason the resulting separation here looks so different from the one above is simply that in this latest series of charts the color selections have essentially been inverted. The inversion creates a mirror mirrored back to the original orientation with the inverted colors in place, and the color reverse is now recognizable

As a matter of course it is helpful to be consistent in the choice of starting color when separating motifs. Any single repeats isolated from above are usable in electronic machines, reduced to black and white squares. Electronics vary in the built separations in terms of choosing black or white squares for the first row knit, whether you download an original image or work with built-in ones. With the preselection of needles in Brother or pushers in Passap, with an easy-to-count color repeat and some air knitting, planning starting color of choice and needle placement can be sorted out for more confidence when actual knitting starts.

If you would prefer to work on graph paper that matches the size of your punchcard, there is a downloadable PDF and word doc with some guidelines in my previous posts more-low-tech/ and creating knit graph paper. The posts were in 2011 and 2014, with illustrations drafted in earlier versions of OS and apps. Working in Pages I was now able to print an image just about to perfect scale to part of a blank factory card. Here is part of the first repeat in this post traced through the punchcard holes onto it:

I then exported 2 documents, one to Word, and the other to PDF. The first printed image and the PDF one (opened in Preview) were printed to an identical scale using my Epson Printer. Here are the new docs for you to try, they may need tweaking. My measurements, adjusted in Pages were 11 cm by 18.2, for 30 rows in card height: PDF no numbers card, Word doc exported from Pages no numbers card. I have found squares of the blank card BMP provided may be filled in either GIMP or Paint, using the paint bucket tool, but the printed size is not in scale to the printout of the original in the pdf.
If the scale does not matter and you prefer convenience, this is a numbered “full” punchcard template as PDF scaled to fit on a single page punchcard numbered, and as an editable Excel document exported from Mac Numbers: punchcard templates_ excel

 

 

Matching patterns across sweater body and sleeves


There is a resurgence of circular yokes on the runways and market at the moment. My previous post discussed some of the considerations in knitting them. For those not up to working that particular way, there are variations in carrying the patterns around the body in continuous lines.

If raglan shaping is used, angular lines are created where patterns meet. All knit is essentially vertical striping. Raglan shaping should match both the front and back of the sleeve, the wider the raglan shape, the less sharp the stripe intersection. Striping in a traditional cap sleeve creates designs that move horizontally across the combined body and arm at rest.

In shaping raglans, however, the angle at which the stripes meet is also crucial in order to be able to use stripes matching in the number of rows. The stitch that is the closest to producing stitches in a square gauge is garter stitch. A charted sample of a mitered, even angled striped square: The start of imagining the graduated angles required in garter stitch for altering the shape, keeping in mind that the number of rows in each angle must match,  The assumption is that if knitting in garter since row gauge and stitch gauge presumably match, any striping on 2 edges at the same angle will also match. Hand knitting patterns can serve as a source of inspiration, garnstudio is a wonderful resource for such patterns, in multiple languages. These patterns are both knit in garter stitch: https://www.garnstudio.com/pattern.php?id=1078&cid=17https://www.garnstudio.com/pattern.php?id=1078&cid=17

In stocking stitch, gauge for stitch and row counts do not match, stripes meeting at different angles will be matching rows to stitches  Sometimes a stocking stitch band is placed between the 2 shapes facilitating matching rows to rows. Space-dyed yarns can create more forgiving intersections https://www.garnstudio.com/pattern.php?id=661&cid=17A stocking stitch sweater pattern for purchase on Ravelry: https://thefibreco.com/product/striped-sweaterMatching is possible with more planning than when using garter stitch, but compromises may need to be made in either or both the width of the body and the raglan sleeve cap, which may alter the amount of fabric pushed forward at the spot where the armhole and the body meet.
In a simple raglan sketch, both sides of each piece are symmetrical. The body’s back neck opening is knit straight across, the front is shaped. The front and back raglan armhole edges, A and B, measure the same, with an equal number of knit rows. The sleeve cap top is straight, helping to form the full-size neckline opening. The small bind-offs of at least one inch at the start of the armhole and raglan shaping help reduce the bulk of fabric in those areas as in when knitting dropped shoulder sweaters

When designing a sweater with a shaped sleeve cap, knit a sample of your stripe pattern. An online stripe generator can help visualize stripe formulas, colorways, etc. If knitting fair isle use row counts for FI pattern height for stripe placement. It is helpful to have a 1 row, 1 stitch graph to plot repeats out. It does not matter if the grid is square or rectangular, providing that vertical and horizontal numbers are based on your gauge. Draw a line from armhole point to armhole on both pattern and sleeve, and there is your match. Work stripe pattern up from armhole line for your cap,  down from line for sleeve repeats.

In my theoretical sweaters, the sleeve’s wrist edge is technically below the armhole to waistline length, so stripes need to be plotted accordingly, from the armhole down.  The same method is used if single motifs or other variations in striping are involved. For single motifs, if matching them in body and sleeve cap, begin by designing them so they fit in the cap’s crown. Place motif in body and sleeve on the same line, and plan the remainder of the sweater calculating from the armhole as for stripes, basing placement on numbers of rows in each design segment.

A collection of online references:
Ravellings on the knitted sleeve By Jenna Wilson
http://knitty.com/ISSUEfall04/FEATfall04TBP.html
http://knitty.com/ISSUEwinter04/FEATwin04TBP.html
http://knitty.com/ISSUEwinter05/FEATwin05TBP.html
math calculators for knitting
https://itunes.apple.com/us/app/knit-evenly-calculator/id370449748?mt=8
“magic formula http://www.getknitting.com/ak_0603triangle.aspx
http://www.getknitting.com/ak_0603mfcalc.aspx#
http://www.getknitting.com/mk_0603frilled.aspx# site is now closed, updated links to find it and other shaping information links may be found in the blog post: Online Pattern generators, hacks, free KM manuals, and more 

 

Revisiting GIMP in knit design

2/2020: Please note: the Mac version of GIMP has been updated and features and appearance. I have begun another post, hoping to illustrate some of the new tools and features over time, it includes links for download of the program and to its manual.

If my only goal is to create illustrations for my posts rather than to produce programmable designs for download to any knitting machine, my go-to program in the past was Excel. Depending on my charting needs, now that Excel is no longer available to me, I am using Mac Numbers or Pages.

My computer is an iMac, with OS High Sierra installed (Mojave update 2019). Last December my 910 was altered to work with Ayab, as mentioned in other posts, via a USB connection to the Mac. For generating files for download I like to work primarily in GIMP (Photoshop is no longer available to me as well). It is freeware. The latest stable Mac Version is version 2.8.22.  Windows users have an option to download a later release. Another freeware option is Paintbrush, a smaller, user-friendly program.

I began sharing my GIMP explorations in mid-2013. Some topics included charting 1, 2, 3, color reductions for 2 color portraits, generated mazes 1 and 2, lace mesh, lace mesh and superimposing, 2 color drop stitch lace

I am using one of my drop stitch designs throughout this post to illustrate steps taken for altering the original by using options such as scaling and tiling. It is intended as a partial quick start guide, not a complete tutorial. The program’s manual provides keyboard shortcuts etc. for anyone wanting to explore more options to obtain similar or other results. That said, the manual is not recently updated or Mac-specific, and Mac vs Windows appearance of windows and menus differ.

To alter and set pixel per stitch options double click on pencil tool,  choose square single-pixel highlighted in brush shape menu

to draw in single pixels, choose show grid, snap to

There are limitations as to how low the magnification may be set before the grid is visible or disappears. I often work in 1,000 magnification. The magnification value numbers, seen at the bottom of the charts in progress, may be typed in, or use arrows to scroll up and down in value 

If your document size is larger, it is sometimes quicker to work in larger pixel size blocks. Here one meets limitations

GIMP large square brushes: numbers indicate desired pixel count and if you are using Paintbrush instead, the “square” is lost

To scale images in height or width without color distortion, change color mode

Image, mode, select Indexed
choose Scale Imagehighlight number you wish to keep constant, whether width or height
to break aspect ratio and control one of the 2 values, click on the chain like symbol on right, it will appear “broken” change the alternate value to the desired number

Click on scale image. If the intent is to continue editing by using the pencil tool, the image mode needs to be returned to RGB before proceeding with editing

You can verify finished image size by choosing scale image again, at that point the chain like symbol on the right of the numbers is “whole” again, awaiting further editing choices

double height double width
 scale may be performed again on the last image created 
the appearance if the image mode is set to RBG, and not indexed prior to scaling

scaling down by half for mylars or for machines that can alter motif to double-wide: 

click to the right of the highlighted number, the “chain” symbol on right remains intact replace the width value, click to the right of the height value and the number will automatically change

Click on the scale option; remember to change image mode prior to doing so if needed; on the left is the image scaled in RGB, on the right in the 1-bit palette

If the image has numbers that have odd numbers in stitch width, the software makes the choice, in assigning values, since no half pixels can be rendered.  For design details see previous post 

Tiling is useful to check how repeats line up when applied to all over the surface of a knit, choosing to alter the horizontal repeat in width or vertical in height, adding borders, and other variations. Ayab software, in particular, requires the individual repeat to be programmed for the number of needles you wish to knit in a pattern on the main bed. Depending on the size of the original motif the tiling function may be used on nearly any scale, with or without a visible grid

To keep aspect ratio, the chain-like symbol on the right of width and height values should be kept whole (first image). It will appear “broken” on side of values from screen grab after the image was tiled when by pulling up the scale option again, to verify pixel counts for the newly created repeat (images 2-4)

to color invert a single repeat or a tiled one  

A Facebook Ayab Group share and tip by Claudia Scarpa brought up a discussion on using Gimp to rescale knits with the intent of estimating distortion in the design as a result of stitch gauge. In many knits aspect ratio is forgiving. In representational knits, it can start to matter significantly. I played with numbers from 3 different gauges, getting back to a simple circle square first, then following up with a much larger image. Starting with pixels per inch setting in scale menu:

doing a bit of math: if the gauge is 5 sts, 7 rows, divide 7 by 5 = 1.4,  6 divided by 4 = 1.5; use the quotient (division result) to modify the respective X and Y values

keeping the X value constant, multiply the Y value by 1.4 for 5 X 7 gauge
in the view menu, uncheck dot to dot prior to selecting scale

keeping the Y value constant, multiply the X value by 1.5 for the 6X4 gauge, uncheck dot to dot if it is available in the view menu to get rid of the math, simply switch to pixels /mm and plug in your gauge. The starting image:

change X and Y resolution to match your stitch and row gauge, breaking “chain link” on right to disable aspect ratio. In order to show the altered scaled image, the dot per dot feature in the view menu needs to be unchecked prior to selecting scale

knitting gauge 5 stitches, 7 rows per inch  4 stitches, 6 rows  per inch and going much larger, using Rocco again: the original version scaled for stitch gauge of 33 X 40

a large geometric .bmp edited with the same process

Claudia Scarpa has created a document on “how to edit a picture with GIMP for “Oknitme software” that she has given permission for me to share here: 03-ENG-gimp. The tutorial has clear instructions for anyone wishing to explore photo editing for use in knits with GIMP, and the Oknitme online tool helps punchcard knitters participate in the process.

If freehand drawing suits your needs, you may find it easier to work with the view settings shown below and adjust pencil pixel size to suit

 

 

Drop stitch lace using Ayab software

Some notes on how tubular software color separations such as the one automated in the ayab circular setting may be found in the previous post

In an effort to respond to a request I have had via my blog, I am sharing information on this topic as I have time to explore it. My first attempt when up and running with the Ayab software, was to reproduce an earlier sample I had created as a color separation originally intended for a hand-knit shadow knit experiment.

a chart from that blog post  try_drop_stitchthe resulting hand knit, on the purl side
IMG_0823the color-separated sample knit pre ayab the sample knit using the Ayab circular setting

Patterns predawn for shadow knitting, appear to be one published source for interesting 2 color drop stitch variations. What about geometric shapes or developing your own designs? Designs created using this technique lengthen considerably when off the machine. Both color sets of stitches become elongated as they are dropped, and that should be a consideration in planning your design. If your goal is a circle, the actual shape programmed may have to be closer to an egg laid horizontally rather than that of a “true” circle. The fabric also widens considerably when blocked and off the machine, making the cast on and bind off methods considerations another necessity. Design repeats may be drawn in Paintbrush or GIMP (both freeware), or Photoshop. I have been a long time GIMP user, and prefer to use it in tiling repeats as opposed to the copy and paste features in Paintbrush to accommodate the Ayab requirement of programming the repeats horizontally in the width of your piece.

In my previous, how-to posts on designing your own 2 color drop stitch lace, part of the color separation required elongating the design X 2. The starting side in Ayab for needle selection always needs to be from left to right, and elongation of the motif is not required when using the Ayab circular option.

This was my first working repeat, A = repeat charted out. B = the working bitmap or png, etc. (which would be the only requirement for the mylar). C = the image tiled for the chosen number of stitches (again, Ayab requires the repeat to be programmed for the width of your knit piece). D = the image elongated, not usable for this fabric, it results in too much elongation. If you would like a knit border on either side, that can be achieved by having extra stitch(es) in work on the ribber. a possible ayab repeat, 56 stitches wide by 36 rows high

The results up to the point in which I had a yarn caught in brushes and stitches dropping on the left of the needle bed:

Drop stitch lace has been referred to over the years in other terms as well, such as release stitch, drive lace, and summer fair isle in Passapese. Passap knitters will recognize the results from this first method are akin to those produced using Technique 185.

Getting started: stitches intended to be dropped may be created on either bed. If the ribber is used to create loops, then the technique is a manual one. Using the main bed in Japanese machines to program dropped stitches increases accuracy and ease.

If you are swatching and testing, a permanent cast on is not necessary. The broken toe cast on is one of the two quickest on the Japanese machines, usable on either bed. It is fondly called that because if ribber cast on comb and weights are in the wrong place so that the wrong loops are dropped, everything falls to the floor, and likely on your toes. There is an online video by Diana Sullivan that shows its use for a tighter cast on row in 1X1 rib, but the use here is for a different purpose.

In producing this fabric you are technically knitting every needle rib. Cast on a fairly tight zig-zag row. The ribber comb wire needs to be placed so that it holds down the stitches on the bed on which you need to keep them. The principle and results are akin to the first row knit when you use a single bed cast on comb, and the second pass, with the first knit row anchors open loops before you continue to knit. Any loops not secured by the comb will result in dropped stitches. Any fabric, any time, when 2 stitches are empty side by side, stitches are not formed and the yarn is dropped off them creating a float or ladder.  The red line indicates the ribber wire on top of the ribber loops in the zigzag row, placed so released knitting will be left on the ribber. Black lines your zig-zag yarn loops, blue dots the teeth of your ribber cast on comb. You can check placement by dropping just a few loops on the main bed before hanging your weights on the comb. 

zigzag row showing the placement of cast on comb teeth, on each side of main bed needles
with wire in place, anchoring ribber stitches testing out dropping a few stitches all stitches now on the  ribber in preparation for dropping stitches created on main bed 

It is possible to also use a wired cast-on comb for an open stitch cast on the top bed only. Remove the wire from the comb. Bring the comb up and between needles to be used, and re-insert wire. Needles and latches will need to travel easily under the wire when the first knit row takes place. 

The knit carriage will not clear the comb properly because of the location of its brushes, etc. For the “cast on” row, exchange the sinker plate on your knit carriage for the one normally used with the ribber. The first photo below shows the approximate location for the comb during the first row knit. Needles are centered between the teeth, the teeth themselves line up with gate pegs. The comb needs to be manually held in place since there is no opposing bed in use to help balance it. Working with the ribber up would ease the process in wider pieces of knitting. The ribber sinker plate has no brushes or wheels to anchor knitting on the knitting bed. Any rows knit single bed using it, will need to have needles brought out to hold position prior to knitting each row for all stitches to be formed properly

the comb in position pass is made slowly with the ribber sinker plate in place the comb is dropped  bring all needles out to hold position  knit one more row, returning to starting position change sinker plate on knit carriage if needed, proceed with knitting

To use the same method with ribber in place: hold the appropriate ribber comb with the bump(s) up facing you, so that the teeth line up with gate pegs as shown above, and so the needles can come through the gaps. Leave the wire in, hold the bump(s) against the ribber, and tilt the comb against the knit bed. Hold the comb high enough to take the carriages across to the opposite side. Move carriages to the other side, drop the comb and weigh it. If continuing on the top bed only drop the ribber, switch sinker plates, and continue to knit.

“bumps”: Brother comb 

For other purposes and an edge similar to a weaving cast-on executed on Japanese machines use EON for the cast-on row, then bring into work and add the rest of the needles prior to knitting the second row.

Use a cast-on comb appropriate for your knitting machine’s gauge ie 4.5mm, 5mm, etc., the brand is not relevant, only tooth spacing is. It is possible to cut ribber cast on combs into different widths for use when knitting is planned on fewer stitches than those accommodated by their available commercial widths.

As for dropping those loops that will form the long stitches, one can do so manually with improvised tools. For more automatic dropping of stitches using knit carriage in Brother patterning, one may punch a card or draw a mylar with a method akin to color separation. A pass of the KH carriage across the knit is made with no yarn in the feeder, color 2 is actually no yarn/empty from left to right while establishing the proper needle selection on its return. The ribber would need to be reset to slip, or the ribber carriage separated from the knit one for the 2 passes to and from the color changer. This is the “scariest” option by far, more error-prone. It is not applicable when using the circular Ayab setting in creating the fabric. Without a specific tool, all stitches can be brought to E and back to B with a ruler, piece of garter bar, ribber cast on comb, or other handy ‘toy’. Dropping stitches is done while carriages are on the left, after the return to the color changer side. It is possible to modify the Studio accessory used to drop stitches

full altered_500

For 2 color drop stitch, the main bed is set to slip in both directions. Because not all needles on the main bed are used for patterning on every row, the KC II setting on the change knob is used, eliminating end needle selection on the 910. The ribber is set to knit every row

Ayab: begin  your design repeat on your first row, choose its circular setting in machine type pull-down menu on the right
The first design row is preselected left to right
The main bed is set to slip <– –>, change knob on KC II (end needle selection is canceled)
Ribber is set to knit <– –> for the duration
COL: as you go from the left to right, needles are preselected on the top bed, they will knit, picking up loops that you will in turn drop on the subsequent passes of the knit carriage from right to left.
COR, the KC knits on preselected needles as it moves to the left.
Clear the color changer, set up your next color. Drop the stitches knit on that last pass

It may be necessary to push those loops down between the beds before you next pass, remember to pull down on your knitting periodically,  visually check needle alignment on the main bed (all needles in B in the work area)

*With the new color move to the right, preselecting the next row of loops
Knit right to left, picking up loops on preselected needles, change colors, drop stitches,** and repeat * to ** steps in 2-row rotations

so I want circles, here is my test pattern more like eggs, the black squares in shape appear as drawn on the purl side shapes are reversed as drawn on the knit side 

It is possible using the circular setting to drop only one of the 2 colors, whether background or shape. I began by dropping the white ground. I used to encourage students to develop a tune/ repeat in their heads when regular actions needed to be taken. For me, in terms of yarn color,  it was “white, knit, drop”,  “brown =  erase (push back to B), go back”. 1: white travels to the right, needles are pre-selected; 2: white travels to left, picking up loops 3: on left, change color, drop stitches. For brown: 1. travel to the right, needles are preselected 2: on the right, before traveling back to left push all selected needles back to B. Only the ribber knits on the way back to left, so brown will have knit 2 rows with no dropped stitches. I ran out of brown yarn, started over with the blue and white, planning on having the shape drop the stitches. There is a difference in the fabric width with the change in the distribution of stitches. I stopped knitting, not due to any mispatterning, but because I encountered another Ayab behavior that may be well known to punchcard knitters. Due to a yarn mast issue, I moved the knit carriage back to disentangle the yarn, and lo and behold the pattern advanced a row.  Punchcard machines will advance a row with any movement of the carriage outside the edges of the knit. This was never an issue in the unaltered 910. At that point, I stopped knitting. 

Not fond of stripes? prefer one color? the sample below was worked on 40 stitches in width, using the repeat charted for 56 stitches. Here decisions are made at the design phase of your repeat. For single color, drop stitch use an image double length, and single setting in the Ayab software. The process is the same: *preselect stitches left to right, knit on selected needles right to left, drop loops just picked up traveling to left**, repeat from * to **. Settings are the same as for the 2 color drop stitch, but the elongation depending on the number of stitches dropped is not as noticeable. The texture in my swatch is diminished after a quick press, the yarn is an acrylic blend. The charted repeat illustrated is wider, but I worked it on only the center 40 stitches. As always in slip stitch, the black squares knit and they represent the stitches that are dropped. If you wish to create the long stitches on the ground (white squares),  reverse use Ayab Action Invert prior to knitting

the chart as viewed and explained at the top of the post

Sources of inspiration from studio publications vary, patterns designed for pile knitting make for suitable one color drop stitch. A partial punchcard repeat

from an electronic collection

and a punchcard pattern book, where markings emulate eyelets, usable only for single color knitting 

Note that in #2 card directly above, there is a solid row at the very start that is a design row (third all punched). In Ayab again, first-row preselection is left to right, you will be picking up loops on preselected needles going from right to left and then dropping them. That first design row needs to have punched holes or black squares/pixels in it. The color separation is essentially done for you in the source image. Do not use circular in Ayab, but rather, use “single” setting and follow instructions for creating the fabric as described above,  with no color changes. The blank punchcard rows match the no selection rows in self-drawn color separations,

If double bed work is daunting, for a different stitch, worked single bed, that may cause interesting distortions in all knit, single bed fabrics see block stitch post.


The self-drawn design repeats for 2 color drop stitch may be offset as well, resulting in colors being dropped alternately.  The design shape needs to be created in 4-row blocks in order for the yarn to make it back and forth to the color changer with both colors to complete one design row. The second pairs of rows in each 4-row block is erased. In this instance as well, rows marked with black squares will pick up loops on the main bed, which are in turn dropped to create the long stitches. The second design repeat is offset to try to get sections of it to create loops to be dropped as well. The final motif must be a multiple of 8 rows in height if it is to be used as Ayab’s infinite repeat in length.
Color changes are indicated in the vertical strip in the center of the design. This was my starting idea

Elongation to 4 rows per block, erasing the second pair of rows for each color on right. The repeat on the right may be used if only one color is to be dropped; the 2 blank rows in the design field represent stitches that will knit only on the ribber for 2 rows. No stitches are dropped in color(s) used in sequential rows of blank squares in all “white” areas of the chart, including multiple rows above and below the design shape. Color changes every 2 rows continue, creating continuous stripes. shapes staggered, visually checking for placement of alternately dropped stitches 

To accommodate the Ayab preselection for the first row to be knit from left to right, move the last blank row in the design to the first-row position. As the carriages travel from left to right and back to the color changer, the stitches will knit 2 rows only on the ribber. Continue knitting in steps as described earlier in the post, changing colors every 2 rows. On a larger knit ground such shapes may be arranged to suit. This was my working repeat, but I used a third fewer stitches in the swatch than in the chart. Note that the images will be reversed on the knit side, so if preferred, use Action Mirror to flip the image horizontally prior to knitting it

The swatch has been quickly pressed, so the texture is flattened out, but I am reminded of a few shadow knits when viewing its purl side.

In an unaltered 910 with the ability to double the width of the programmed repeat, mylar users are not excluded from exploring a similar fabric. The repeat above may be rescaled to half the width,  drawn that way, and then use the twice as wide built-in feature. Gimp does an “interesting” thing when scaling this design to half-width, note the right side of each repeat is an odd number of squares, the left side an even. The repeat may be used as-is or redrawn, adding or eliminating black squares if symmetry in each shape matters.  Paintbrush produces the same image, mirrored.

The explanation: further analysis of the original design reveals the fact that some of the pixel numbers in the design black square blocks are uneven in width. In this instance, 3.5 is half of 7, and half pixels cannot be rendered, so the software assigns the split to 4 and 3.  

 

Lace punchcards meet Ayab

1/8/18 It appears I now have acquired preselection from left to right on the first pass with my Ayab software, which I have been told is its “normal”. I am revising the information I have offered since I began working with Ayab if needed because of this, beginning with lace. This punchcard design is worked with each carriage operating for 2 rows, and all transfers in the same direction. The LC (lace carriage) on left, the KC (knit carriage) on right. An added note: sometimes punchcard designs may be used as provided, not altering the repeat in any way. Accidentally marking squares or pixels in the wrong spot, or deliberately starting with the LC on the wrong side, may still produce interesting fabrics. As always keeping good notes is more than well worth it. punchcard actions: transfers are all to the left (seen leaning to right on the knit side)With the first preselection row using Ayab beginning with the LC on the left, the same transfer sequences occur as in the punchcard machine or a single repeat on a mylar

swatch knit with the LC operating on the left, the KC on right throughout

For use with the color changer, the same repeat may be used. Transfers, however, now need to occur with the LC operating on the right giving the knit carriage the opportunity to travel to and from the color changer in 2 (or more, even #) row sequences. Using a punchcard, one would turn a punchcard over before inserting it into the card reader to work with the LC beginning on and continuing from the right. To achieve the same fabric using Ayab, shift the top row to the bottom of the repeat, and either mirror your image prior to importing it into Ayab, or use its mirror action in the pull-down menu. The chart shows the repeat prior to mirroring, with desired actions described to its right. It is not possible to read the first row from beyond the right set line using Ayab, so the LC begins on the left, travels to the right on the first blank row, selects on the second pass to the left, transfers stitches as it travels to the right again and stays there, operating from that side for the remainder of the knit. All transfers are now reversed and made to the right, and seen leaning to left on the knit side of the fabric. After the first 3 LC passes, each carriage operates for 2 rows at a time, all transfers are to the right, lean to the left on the knit side of the fabric.

Possible striping choices:  the differences between areas marked A or B is in the location of the color change. In A areas the color is changed immediately after the single transfer at the top of the “triangle”, in B areas the last eyelet is completed in the same color used up to that point, and the color change is made after the first row of 4 transfers at the base of the “triangle”. More complex lace repeats create much more interesting variations in the direction and movement of the stripes.
 verification on a different day, LC on Left, repeat not mirrored 
The punchcard for fabric from 1/25/18 post. This fabric creates large eyelets, there will be 2 empty needles side by side for the duration. Some of the old pattern books referred to it as one of the “mock crochet” ones. 

operating with LC on the left operating with the LC on the right: the repeat is mirrored  

the original repeat (re-worked on 24 sts)Ayab for operating with the LC on the left, repeat is mirrored  Ayab for knitting with LC on the right, original repeat, rows split

The bottom of the swatch was knit with the LC operating from Left, the top with the LC operating from right after its third pass illustrated in the “triangle” lace description above repeated testing, bottom LC operating from left, top LC operating from right For a discussion of the same punchcard worked in a variety of ways see Lace meets weaving on Brother machines. 
for full details. The punchcard was originally designed for operating both the knit and the LC carriages from the right. If KC I is used resulting in end needle selection on only the first and last needles in use, prior to passes of the LC push those needles back to B. If there are 3 empty needles on the edge on either side on rows preselected for weaving, bring the outside needle to work/ E prior to laying in the weaving yarn.  The image tiled for the width of my knit, in this case, 32 stitches, a multiple of 8I actually cast on an extra stitch on each side at the beginning of the piece with the intent they not be in pattern and create a single knit stitch border in areas of transfers. Here are the results, barring a couple of spots the weaving yarn did not get caught properly. The pattern as drawn produces a fabric that is interesting, but different than the intended With the pattern flipped horizontally / mirrored, we now have the same results as in using the 589 punchcard

So to mirror or not to mirror? that is the question… I tested  643 and 650 from Pattern book #5, found mirroring was indeed required for transfer accuracy. I  verified that the “triangles” do not need to be mirrored to match the punchcard swatch. The notable difference in the latter is that all transfers are in the same direction and that each carriage operates for only 2 rows.

Two more to try, directions are not ayab specific: a large diagonal eyelet lace combining lace and tuck 

12/28/17: tuck lace meets hand technique 

For more lace samples and symbols and suggestions from punchcard books on knitting the fabric, please see punch-card-book-symbols-and-samples

A Fair isle sample with deliberately mirrored lettering proved the program knits what it sees, so my letters were still reversed, as drawn.

On 12/25/17 I shared my first try at lace using Ayab and the workaround for the first pre-selection row occurring from left to right. The LC is the one to select for transfers, the KC knits to complete the formation of stitches. Brother punchcards for lace usually begin with selection rows, end with 2 blank rows at their top. Because Ayab requires a first pass from left to right for the next row to be selected, to get the pattern to work one needs to split the 2 rows at the top, bringing one of them down to the start of the repeat. If knitting continues with the LC pattern as originally drawn, the transfers will occur in the opposite direction of that intended. To work around that, the image may be mirrored in the paint program before download, or use action/mirror in the Ayab menu before knitting. One nice added feature is that blank rows may be left at both sides, creating a knit stitch border, and eliminating the problem of paying attention as to whether end needles are selected or not, and what measures to take. This fabric creates large eyelets, there will be 2 empty needles side by side for the duration. Some of the old pattern books referred to it as one of the “mock crochet” ones. These repeats do not hold with first-pass preselection from the left.

the original repeat the repeat mirrored the resulting fabric, knit and purl sides

no mirroring, software patterning errors in one of the test swatches 
operating from the right, using the color changer

“Crochet” meets machine knitting techniques: tuck lace trims or fabrics 2

There have been several previous posts on “crochet” like stitches and “tuck lace”, this is another variant. The needles need to be arranged as in the diagrams below. After the first preselection row, the carriage is set to tuck

the full punchcard T= areas where tuck loops will occur, K = knit columns, o = NOOW, the red line the 0 mark on the needle tape

Every 5 rows, after the tuck loops are knit together (illustrated in repeats on far left), the formed stitch (single black square) is transferred in turn to the right and then to left; this works out happily so that transfers may always be made toward the knit carriage.
The sole repeat (all that would be required on a mylar) is 4 stitches wide, 5 rows high. The number of needles used needs to be planned so that there is a knit stitch on either end of the piece. This is accomplished by using a repeated multiple of 4 + 1, so one side of the 0 mark has an even number of stitches, the other an odd (4+1=5). Ayab software requires that the repeat is programmed across the width of the fabric, so the final design would be a variant of this, my sample was worked on 20 left, 17 right. Non selected needles form tuck loops until they are knit together every 5th row

If you prefer to work with the top repeat programmed, then transfers will need to be made on each side of the non-selected needles to get the proper configuration. If programmed with the bottom repeat, then and every other needle cast on is fine. I generally stay away from combs and weights if I can, but this is a fabric that benefits by evenly distributed weight, a cast-on comb with weights added to it is a good idea. In the absence of any, start with waste yarn and ravel cord, thread a thin knitting needle or wire through the knit, and hang evenly spaced weights on that. Follow with your preferred cast on, and knitting in pattern. 

The swatch as it appears on the purl side (traditional “public side” for tuck stitch). The bottom 4 repeats show what the fabric looks like before one intervenes with the hand technique

its knit side and a bit closer a few more

in early publications combinations of lace and tuck, creating a large scale mesh were also referred to as mock crochet